ASTM C1802-14e1
Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
- Standard No.
- ASTM C1802-14e1
- Release Date
- 2014
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C1802-18
- Latest
- ASTM C1802-23
- Scope
- 1.1 This specification covers the design, testing, manufacture, selection, and installation of fabricated metal access hatches for utility, water, and wastewater structures including utility vaults, drainage structures, valve vaults, meter vaults, wet wells, pump enclosures, utility trenches, piping trenches, and drainage trenches. 1.2 This specification is applicable to various configurations of access hatches constructed of fabricated metal of various materials and grades for various loading conditions, traffic speeds, or both. 1.3 Engineering design and testing criteria are provided for access hatches to be located in various areas subjected to various loading conditions, traffic speed, frequency, or combinations thereof. 1.4 Proof loading criteria is provided to allow the access hatches to be designed by engineering calculation and/or by ultimate strength load testing. 1.5 Production loading criteria is provided to allow the access hatches to be tested to verify the load capacity of the manufactured hatches. 1.6 Hatch loading selection guidelines are included to allow selection of the proper hatch design loading for the conditions of the actual area of placement. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered the standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM C1802-14e1 Referenced Document
- ANSI/AISC 360 Specification for Structural Steel Buildings*， 2024-04-22 Update
- ASTM A123/A123M Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products*， 2024-04-22 Update
- ASTM A176 Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip
- ASTM A240/A240M Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
- ASTM A242/A242M Standard Specification for High-Strength Low-Alloy Structural Steel*， 2024-03-01 Update
- ASTM A276 Standard Specification for Stainless Steel Bars and Shapes
- ASTM A325 Standard Specification for High-Strength Bolts For Structural Steel Joints
- ASTM A36/A36M Standard Specification for Carbon Structural Steel
- ASTM A490 Standard Specification for Quenched And Tempered Alloy Steel Bolts For Structural Steel Joints
- ASTM A500/A500M Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes*， 2023-11-01 Update
- ASTM A514/A514M Standard Specification for High-Yield- Strength, Quenched And Tempered Alloy Steel Plate, Suitable For Welding*， 2024-04-22 Update
- ASTM A529/A529M Standard Specification for High-Strength Carbon-Manganese Steel of Structural Quality*， 2019-05-01 Update
- ASTM A53/A53M Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
- ASTM A572/A572M Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel*， 2021-05-15 Update
- ASTM A588/A588M Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance*， 2019-09-01 Update
- ASTM A618/A618M Standard Specification for Hot-Formed Welded and Seamless High-Strength Low-Alloy Structural Tubing*， 2024-04-22 Update
- ASTM A656/A656M Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability*， 2024-03-01 Update
- ASTM A666 Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar*， 2023-03-01 Update
- ASTM A786/A786M Standard Specification for Hot-Rolled Carbon, Low-Alloy, High-Strength Low-Alloy, and Alloy Steel Floor Plates*， 2021-09-01 Update
- ASTM A847/A847M Standard Specification for Cold-Formed Welded and Seamless High-Strength, Low-Alloy Structural Tubing with Improved Atmospheric Corrosion Resistance*， 2024-04-22 Update
- ASTM A852/A852M Standard Specification for Quenched and Tempered Low-Alloy Structural Steel Plate with 70 ksi [485 MPa] Minimum Yield Strength to 4 in. [100 mm] Thick *， 2024-04-22 Update
- ASTM A913/A913M Standard Specification for High-Strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-Tempering Process (QST)*， 2019-09-01 Update
- ASTM A992/A992M Standard Specification for Structural Steel Shapes*， 2022-09-01 Update
- ASTM B209 Standard Specification for Aluminum and Aluminum- Alloy Sheet and Plate
- ASTM B210 Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
- ASTM B211 Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
- ASTM B221 Standard Specification for Aluminum-Alloy Extruded Bars, Rods, Wire, Shapes, and Tubes
- ASTM B241/B241M Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
- ASTM B247 Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings*， 2020-05-01 Update
- ASTM B308/B308M Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles*， 2020-01-01 Update
- ASTM B316/B316M Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods*， 2020-12-01 Update
- ASTM B429/B429M Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube*， 2020-11-01 Update
- ASTM B632/B632M Standard Specification for Aluminum-Alloy Rolled Tread Plate*， 2018-08-01 Update
- ASTM B928/B928M Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments*， 2023-10-01 Update
- ASTM C478 Standard Specification for Precast Reinforced Concrete Manhole Sections
- ASTM C857 Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures
- ASTM C890 Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures
- ASTM E2309/E2309M Standard Practices for Verification of Displacement Measuring Systems and Devices Used in Material Testing Machines*， 2020-02-01 Update
- ASTM E4 Standard Practices for Force Verification of Testing Machines
- ASTM F467 Standard Specification for Nonferrous Nuts for General Use
- ASTM F468 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
ASTM C1802-14e1 history
- 2023 ASTM C1802-23 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
- 2020 ASTM C1802-20 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
- 2018 ASTM C1802-18b Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Horizontal Access Hatches for Utility, Water, and Wastewater Structures
- 2018 ASTM C1802-18a Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Horizontal Access Hatches for Utility, Water, and Wastewater Structures
- 2018 ASTM C1802-18 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
- 2014 ASTM C1802-14e1 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
- 2014 ASTM C1802-14 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
