ASTM C1802-23 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
1.1 This specification covers the design, testing, manufacture, selection, and installation of substantially horizontal fabricated metal access hatches for utility, water, and wastewater structures including utility vaults, drainage structures, valve vaults, meter vaults, wet wells, pump enclosures, utility trenches, piping trenches, and drainage trenches. 1.2 This specification is applicable to various configurations of access hatches constructed of fabricated metal of various materials and grades for various loading conditions, traffic speeds, or both. 1.3 Engineering design and testing criteria are provided for access hatches to be located in various areas subjected to various loading conditions, traffic speed, frequency, or combinations thereof. 1.4 Proof loading criteria is provided to allow the access hatches to be designed by engineering calculation and/or by ultimate strength load testing. 1.5 Production loading criteria is provided to allow the access hatches to be tested to verify the load capacity of the manufactured hatches. 1.6 Hatch loading selection guidelines are included to allow selection of the proper hatch design loading for the conditions of the actual area of placement. 1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered the standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C1802-23 Referenced Document
ANSI/AISC 360 Specification for Structural Steel Buildings*, 2024-04-21 Update
ASTM A123/A123M Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products*, 2024-04-21 Update
ASTM A176 Standard Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip
ASTM A240/A240M Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ASTM A242/A242M Standard Specification for High-Strength Low-Alloy Structural Steel*, 2024-03-01 Update
ASTM A276/A276M Standard Specification for Stainless Steel Bars and Shapes*, 2024-02-01 Update
ASTM A325 Standard Specification for High-Strength Bolts For Structural Steel Joints
ASTM A36/A36M Standard Specification for Carbon Structural Steel
ASTM A490 Standard Specification for Quenched And Tempered Alloy Steel Bolts For Structural Steel Joints
ASTM A500/A500M Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes*, 2023-11-01 Update
ASTM A514/A514M Standard Specification for High-Yield- Strength, Quenched And Tempered Alloy Steel Plate, Suitable For Welding*, 2024-04-21 Update
ASTM A529/A529M Standard Specification for High-Strength Carbon-Manganese Steel of Structural Quality
ASTM A53/A53M Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
ASTM A572/A572M Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
ASTM A588/A588M Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance
ASTM A618/A618M Standard Specification for Hot-Formed Welded and Seamless High-Strength Low-Alloy Structural Tubing*, 2024-04-21 Update
ASTM A656/A656M Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability*, 2024-03-01 Update
ASTM A666 Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
ASTM A786/A786M Standard Specification for Hot-Rolled Carbon, Low-Alloy, High-Strength Low-Alloy, and Alloy Steel Floor Plates
ASTM A847/A847M Standard Specification for Cold-Formed Welded and Seamless High-Strength, Low-Alloy Structural Tubing with Improved Atmospheric Corrosion Resistance*, 2024-04-21 Update
ASTM A852/A852M Standard Specification for Quenched and Tempered Low-Alloy Structural Steel Plate with 70 ksi [485 MPa] Minimum Yield Strength to 4 in. [100 mm] Thick *, 2024-04-21 Update
ASTM A913/A913M Standard Specification for High-Strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-Tempering Process (QST)
ASTM A992/A992M Standard Specification for Structural Steel Shapes
ASTM B209/B209M Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
ASTM B210/B210M Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
ASTM B211/B211M Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire*, 2023-10-01 Update
ASTM B221 Standard Specification for Aluminum-Alloy Extruded Bars, Rods, Wire, Shapes, and Tubes
ASTM B241/B241M Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
ASTM B247 Standard Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings
ASTM B308/B308M Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles
ASTM B316/B316M Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
ASTM B429/B429M Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube
ASTM B632/B632M Standard Specification for Aluminum-Alloy Rolled Tread Plate
ASTM B928/B928M Standard Specification for High Magnesium Aluminum-Alloy Products for Marine Service and Similar Environments*, 2023-10-01 Update
ASTM C478/C478M Standard Specification for Circular Precast Reinforced Concrete Manhole Sections
ASTM C857 Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures
ASTM C890 Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures
ASTM E2309/E2309M Standard Practices for Verification of Displacement Measuring Systems and Devices Used in Material Testing Machines
ASTM E4 Standard Practices for Force Verification of Testing Machines
ASTM F467 Standard Specification for Nonferrous Nuts for General Use
ASTM F468 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
ASTM C1802-23 history
2023ASTM C1802-23 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
2020ASTM C1802-20 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Horizontal Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
2018ASTM C1802-18b Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Horizontal Access Hatches for Utility, Water, and Wastewater Structures
2018ASTM C1802-18a Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Horizontal Access Hatches for Utility, Water, and Wastewater Structures
2018ASTM C1802-18 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
2014ASTM C1802-14e1 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures
2014ASTM C1802-14 Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Access Hatches for Utility, Water, and Wastewater Structures