1.1 This specification covers aluminum-alloy extruded structural pipe and tube in those selected alloys shown in Table 1 and tempers shown in Table 2, and in those standard sizes shown in Tables 3-5, as well as in other nonstandard sizes as agreed upon between the purchaser and supplier. Such pipe and tube is intended for use in structural applications such as highway and bridge rails, chain-link fence posts, handrails, sign structures, awning supports, lighting brackets, etc. Structural pipe and tube is not intended for fluid-carrying applications involving pressure. NOTE 1—For drawn seamless tube used in pressure applications see Specifications B210/B210M, for seamless pipe and seamless extruded tube used in pressure applications see Specifications B241/B241M, and for drawn tube and pipe for general purpose applications see Specification B483/B483M.
1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9 (for example, A96061 for alloy 6061 in accordance with Practice E527).
1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.
1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.4.1 Metric Sizes—While this is a combined SI and inchpound units specification, there are no standard equivalent metric designations for pipe. Metric sizes are converted and shown only for user convenience.
1.4.2 While this is a combined SI and inch-pound units specification, standard pipe sizes are not applicable to SI units, therefore non-rationalized SI units (soft conversions) are shown for reader convenience. Rationalized [hard converted] SI units are shown in brackets while non-rationalized (soft converted) SI units are shown in parentheses.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B429/B429M-20 Referenced Document
ASTM B210/B210M Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
ASTM B241/B241M Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube
ASTM B483/B483M Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications*, 2021-10-22 Update
ASTM B557 Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
ASTM B557M Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric]
ASTM B660 Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
ASTM B666/B666M Standard Practice for Identification Marking of Aluminum and Magnesium Products
ASTM B807/B807M Standard Practice for Extrusion Press Solution Heat Treatment for Aluminum Alloys
ASTM B881 Standard Terminology Relating to Aluminum- and Magnesium- Alloy Products
ASTM B918/B918M Standard Practice for Heat Treatment of Wrought Aluminum Alloys*, 2020-12-01 Update
ASTM B945 Standard Practice for Aluminum Alloy Extrusions Press Cooled from an Elevated Temperature Shaping Process for Production of T1, T2, T5 and T10-Type Tempers*, 2021-12-01 Update
ASTM B985 Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis*, 2024-04-20 Update
ASTM E1251 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge
ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
ASTM E3061 Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Inductively Coupled Plasma Atomic Emission Spectrometry (Performance Based Method)*, 2024-04-20 Update
ASTM E34 Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
ASTM E527 Standard Practice for Numbering Metals and Alloys (UNS)
ASTM E607 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique, Nitrogen Atmosphere
ASTM E716 Standard Practices for Sampling Aluminum and Aluminum Alloys for Spectrochemical Analysis
ASTM B429/B429M-20 history
2020ASTM B429/B429M-20 Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube
2010ASTM B429/B429M-10e1 Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube
2010ASTM B429/B429M-10 Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube
2006ASTM B429/B429M-06 Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube
2002ASTM B429-02 Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube
2000ASTM B429-00 Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube