This standard specifies the dimensional requirements both for test specimens made of plastic masses intended for processing by molding and for test specimens produced by processing plates or molded bodies. The standard contains in one document the names and dimensions of the test specimens used to record comparable data and also other frequently used test specimens.
EN ISO 20753:2014 Referenced Document
ASTM D1822-06 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials*， 2024-04-20 Update
IEC 60112:2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60426:2007 Electrical insulating materials - Determination of electrolytic corrosion caused by insulating materials - Test methods
ISO 10350-1:2007 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
ISO 10350-2:2001 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics
ISO 10724-1:1998 Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens
ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method
ISO 1183-3:1999 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
ISO 178:2010 Plastics - Determination of flexural properties
ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test
ISO 179-2:1997 Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test
ISO 180:2000 Plastics - Determination of Izod impact strength
ISO 2039-1:2001 Plastics - Determination of hardness - Part 1: Ball indentation method
ISO 2039-2:1987 Plastics; Determination of hardness; Part 2 : Rockwell hardness
ISO 2818:1994 Plastics - Preparation of test specimens by machining
ISO 293:2004 Plastics - Compression moulding of test specimens of thermoplastic materials
ISO 294-1:1996 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 294-2:1996 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 2: Small tensile bars
ISO 294-3:2002 Plastics - Injection moulding of test specimens of thermoplastics materials - Part 3: Small plates
ISO 294-5:2011 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy
ISO 295:2004 Plastics - Compression moulding of test specimens of thermosetting materials
ISO 306:2013 Plastics.Thermoplastic materials.Determination of Vicat softening temperature (VST)
ISO 3167:2002 Plastics - Multipurpose test specimens
ISO 4589-2:1996 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test
ISO 4589-3:1996 Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test
ISO 527-2:1993 Plastics; determination of tensile properties; part 2: test conditions for moulding and extrusion plastics
ISO 604:2002 Plastics - Determination of compressive properties
ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite
ISO 8256:2004 Plastics - Determination of tensile-impact strength
ISO 868:2003 Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness)
ISO 899-1:2003 Plastics - Determination of creep behaviour - Part 1: Tensile creep
ISO 899-2:2003 Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading