ISO 10350-1:2007
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials

Standard No.

ISO 10350-1:2007

Release Date

2007

Published By

International Organization for Standardization (ISO)

Status

Be replaced

Replace By

ISO 10350-1:2007/Amd 1:2014

Latest

ISO 10350-1:2017

Scope

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturers' data sheets. This part of ISO 10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350, long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.

ISO 10350-1:2007 Referenced Document

• ISO 1 Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties*， 2022-06-14 Update
• ISO 10724-1 Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens
• ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics; Technical Corrigendum 1
• ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method*， 2019-02-28 Update
• ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*， 2019-02-28 Update
• ISO 1183-3 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
• ISO 178 Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers*， 2019-04-01 Update
• ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*， 2023-06-07 Update
• ISO 179-2 Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test — Amendment 1: Precision data*， 2020-05-14 Update
• ISO 2577 Plastics - Thermosetting moulding materials - Determination of shrinkage*， 2007-12-01 Update
• ISO 2818 Plastics — Preparation of test specimens by machining*， 2018-12-13 Update
• ISO 291 Plastics - Standard atmospheres for conditioning and testing*， 2008-05-01 Update
• ISO 293 Plastics — Compression moulding of test specimens of thermoplastic materials*， 2023-02-21 Update
• ISO 294-1 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens*， 2017-05-01 Update
• ISO 294-3 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates*， 2020-06-26 Update
• ISO 294-4 Milling cutters mounted on centring arbors having a 7/24 taper; Fitting dimensions; Centring arbors*， 2018-12-20 Update
• ISO 295 Plastics - Compression moulding of test specimens of thermosetting materials
• ISO 306 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)*， 2022-11-18 Update
• ISO 3167 Plastics - Multipurpose test specimens*， 2014-08-01 Update
• ISO 4589-2 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test*， 2017-04-01 Update
• ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles*， 2019-07-26 Update
• ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics*， 2012-02-01 Update
• ISO 6603-2 Plastics. Determination of puncture impact behaviour of rigid plastics. - Part 2: Instrumented impact testing*， 2023-06-02 Update
• ISO 75-1 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics*， 2020-02-28 Update
• ISO 75-2 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite*， 2013-04-01 Update
• ISO 8256 Plastics*， 2023-11-01 Update
• ISO 899-1 Plastics - Determination of creep behaviour - Part 1: Tensile creep*， 2017-09-01 Update

ISO 10350-1:2007 history

• 2017 ISO 10350-1:2017 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
• 2014 ISO 10350-1:2007/Amd 1:2014 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials; Amendment 1
• 2007 ISO 10350-1:2007 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
• 1998 ISO 10350-1:1998 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials