This European Standard is applicable to gully tops and manhole tops made of flake graphite cast iron and/or spheroidal graphite cast iron whether in combination with concrete or not, with a clear opening up to and including 1000 mm for covering gullies, manholes and inspection chambers for installation within areas subjected to pedestrian and/or vehicular traffic. It is applicable to manhole tops and gully tops for use in- areas which can only be used by pedestrians and pedal cyclists (at least class A 15); - pedestrian areas and comparable areas, car parks or car parking decks (at least class B 125); - the area of kerbside channels of roads which, when measured from the kerb edge, extends a maximum of 0,5 m into the carriageway and a maximum of 0,2 m into the pedestrian area (at least class C 250); - carriageways of roads (including pedestrian streets), hard shoulders and parking areas, for all types of road vehicles (at least class D 400); - areas imposing high wheel loads, e. g. docks, aircraft pavements (at least class E 600); - areas imposing particularly high wheel loads, e. g. aircraft pavements (class F 900). This European Standard is not applicable in isolation but only in combination with EN 124-1 and gives guidance for combinations of covers/grating made of cast iron with frames according to EN 124-3, EN 124-4, EN 124-5 or EN 124-6. This European Standard is not applicable to; - cover fillings installed on site, e. g. concrete, paving blocks, etc; - concave gratings for class D 400 installed in carriageways of roads or hard shoulders and concave gratings for classes F 900 and E 600; - gratings/covers as part of prefabricated drainage channels according to EN 1433; - floor and roof gullies in buildings which are specified in EN 1253 (all parts); and; - surface boxes.
EN 124-2:2015 Referenced Document
EN 124-1:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 1: Definitions@ classification@ general principles of design@ performance requirements and test methods
EN 124-3:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 3: Gully tops and manhole tops made of steel or aluminium alloys
EN 124-4:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 4: Gully tops and manhole tops made of steel reinforced concrete
EN 124-5:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials
EN 124-6:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 6: Gully tops and manhole tops made of polypropylene (PP)@ polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U)
EN 1253-1:2015 Gullies for buildings - Part 1: Trapped floor gullies with a depth water seal of at least 50 mm
EN 1253-2:2015 Gullies for buildings - Part 2: Roof drains and floor gullies without trap
EN 1253-3:1999 Gullies for Buildings - Part 3: Quality Control
EN 1253-4:1999 Gullies for Buildings - Part 4: Access Covers
EN 1253-5:2003 Gullies for buildings - Part 5: Gullies with light liquids closure*， 2024-04-20 Update
EN 1433:2002 Drainage channels for vehicular and pedestrian areas - Classification, design and testing requirements, marking and evaluation of conformity*， 2024-04-20 Update
EN 1561:2011 Founding - Grey cast irons*， 2024-04-20 Update
EN 1563 Founding - Spheroidal graphite cast irons*， 2018-08-01 Update
EN 206:2013 Concrete - Specification@ performance@ production and conformity (Incorporates Amendment A1: 2016)*， 2024-04-20 Update
EN 124-2:2015 history
2015EN 124-2:2015 Gully tops and manhole tops for vehicular and pedestrian areas - Part 2: Gully tops and manhole tops made of cast iron