ISO 16396-2:2017
Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
- Standard No.
- ISO 16396-2:2017
- Release Date
- 2017
- Published By
- International Organization for Standardization (ISO)
- Status
- Replace By
- ISO 16396-2:2022
- Latest
- ISO 16396-2:2022
ISO 16396-2:2017 Referenced Document
- IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
- IEC 60112:2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
- IEC 60243-1:2013 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
- IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
- IEC 60296:2012 Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear
- IEC 60695-11-10:2013 Fire hazard testing.Part 11-10: Test flames.50 W horizontal and vertical flame test methods
- ISO 10350-1:2007 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
- ISO 1110:1995 Plastics - Polyamides - Accelerated conditioning of test specimens
- ISO 1133-2:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture
- ISO 11357-3:2011 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization
- ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method
- ISO 1183-2:2004 Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method
- ISO 1183-3:1999 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
- ISO 15512:2016 Plastics - Determination of water content
- ISO 16396-1:2015 "0000Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications"
- ISO 179-1:2010 Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test
- ISO 179-2:1997 Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test
- ISO 20753:2008 Plastics - Test specimens
- ISO 27547-1:2010 Plastics - Preparation of test specimens of thermoplastic materials using mouldless technologies - Part 1: General principles, and laser sintering of test specimens
- ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing
- ISO 294-1:1996 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens
- ISO 294-3:2002 Plastics - Injection moulding of test specimens of thermoplastics materials - Part 3: Small plates
- ISO 294-4:2001 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 4: Determination of moulding shrinkage
- ISO 307:2007 Plastics - Polyamides - Determination of viscosity number
- ISO 3451-4:1998 Plastics - Determination of ash - Part 4: Polyamides
- ISO 472:2013 Plastics - Vocabulary
- ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics
- ISO 62:2008 Plastics - Determination of water absorption
- ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite
- ISO 8256:2004 Plastics - Determination of tensile-impact strength
ISO 16396-2:2017 history
- 2022 ISO 16396-2:2022 Plastics — Polyamide (PA) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
- 2017 ISO 16396-2:2017 Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
