ASTM C505-15
Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints
- Standard No.
- ASTM C505-15
- Release Date
- 2015
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C505-19
- Latest
- ASTM C505-19
- Scope
1.1 This specification covers nonreinforced concrete pipe with rubber gasket joints to be used for the conveyance of irrigation water with working pressures, including hydraulic transients, as shown in Table 1.
(A) Thinner walls are not prohibited on pipe units not over 4 ft in length, but the thickness of such walls shall not be less than the internal diameter divided by 10.(B) With the exception of 21 and 24-in. pipe, higher working pressures are not prohibited to be used up to a maximum of 50 ft for 6 through 12-in. diameters, and 40 ft for 15 through 18-in. diameters. In these cases the strength of the pipe shall be increased to give minimum internal hydrostatic test pressures of at least three times the design working pressure when tested as specified in 10.4.(C) For hydrostatic test requirements, refer to 10.4.1.2 A complete metric companion to Specification C505 has been developed—C505M; therefore, no SI equivalents are presented in this specification.
Note 1: This specification is for manufacturing and purchase only and does not include requirements for bedding, backfill, installation, or field repairs. The owner is cautioned that he must correlate field conditions with the characteristics of the pipe specified and provide inspection during installation.
ASTM C505-15 Referenced Document
- ASTM C1017/C1017M Standard Specification for Chemical Admixtures for Use in Producing Flowing Concrete
- ASTM C1116/C1116M Standard Specification for Fiber-Reinforced Concrete
- ASTM C150/C150M Standard Specification for Portland Cement
- ASTM C1602/C1602M Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
- ASTM C260/C260M Standard Specification for Air-Entraining Admixtures for Concrete
- ASTM C33/C33M Standard Specification for Concrete Aggregates
- ASTM C494/C494M Standard Specification for Chemical Admixtures for Concrete
- ASTM C497 Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile
- ASTM C595/C595M Standard Specification for Blended Hydraulic Cements
- ASTM C618 Standard Specification for Fly Ash And Raw Or Calcined Natural Pozzolan For Use As A Mineral Admixture In Portland Cement Concrete
- ASTM C822 Standard Terminology Relating to Concrete Pipe and Related Products
- ASTM C989/C989M Standard Specification for Slag Cement for Use in Concrete and Mortars
- ASTM D1149 Standard Test Method for Rubber Deterioration-Surface Ozone Cracking in a Chamber
- ASTM D1415 Standard Test Method for Rubber Property—International Hardness
- ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-20 Update
- ASTM D395 Standard Test Methods for Rubber Property-Compression Set
- ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers8212;Tension
- ASTM D471 Standard Test Method for Rubber Property-Effect of Liquids
- ASTM D573 Standard Test Method for Rubber-Deterioration in an Air Oven
ASTM C505-15 history
- 2019 ASTM C505-19 Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints
- 2015 ASTM C505-15 Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints
- 2011 ASTM C505-11 Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints
- 2005 ASTM C505-05a Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints
- 2005 ASTM C505-05 Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints
- 2003 ASTM C505-03 Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints
- 1999 ASTM C505-99a Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints
