AQ 9003.1-2008
Technical specifications for production safety monitoring systems based on network.Part 1: Technical specifications for the connecting of monitoring systems based on network in hazardous area (English Version)

Standard No.

AQ 9003.1-2008

Language

Chinese, Available in English version

Release Date

2008

Published By

Professional Standard-Safe Production

Latest

AQ 9003.1-2008

Scope

This specification defines terms related to networked monitoring systems in hazardous locations, stipulates the front-end composition, software, hardware and interface requirements of the monitoring system, as well as technical requirements for on-site access, power supply, grounding, on-site construction, etc. It is an important tool for constructing and evaluating hazardous location networks. The basic basis of chemical monitoring system. This specification is applicable to safety production enterprises (hereinafter referred to as enterprises) that are subject to network monitoring as defined by national laws, regulations or standards. Other units or departments can refer to this when constructing or evaluating network monitoring systems for hazardous locations. In addition to strictly complying with this specification, the on-site access to the networked monitoring system for hazardous locations should also comply with the relevant national mandatory standards.

AQ 9003.1-2008 Referenced Document

• CECS 81-1996 Technical code for anti-interference of industrial computer monitoring and controlling system
• GB 3836.1 Explosive atmospheres.Part 1:Equipment.General requirements*， 2010-08-09 Update
• GB 3836.10 Electrical apparatus for explosive atmospheres--Hermetically sealed electrical apparatus "h"
• GB 3836.11 Explosive atmospheres.Part11:Equipment protection by flameproof enclosures"d"method of test for ascertainment of maximum experimental safe gap
• GB 3836.12 Explosive atmospheres.Part 12:Classification of mixtures of gases or vapours with air according to their maximum experimental safe gaps and minimum igniting current
• GB 3836.13 Explosive atmospheres.Part 13:Equipment repair, overhaul and reclamation*， 2013-12-17 Update
• GB 3836.14 Explosive atmospheres.Part 14:Classification of areas.Explosive gas atmosphere*， 2014-12-05 Update
• GB 3836.15 Electrical apparatus for explosive gas atmospheres. Part 15: Electrical installation in hazardous areas (other than mines)
• GB 3836.16 Electrical apparatus for explosive gas atmospheres.Part 16:Inspection and maintenance of electrical installation(other than mines)
• GB 3836.17 Electrical apparatus for explosive gas atmosphere Part 17: Construction and use of rooms or buildings protected by pressurization
• GB 3836.18 Explosive atmospheres.Part 18:Intrinsically safe system*， 2010-08-09 Update
• GB 3836.19 Explosive atmospheres.Part 19:Fieldbus intrinsically safe concept (FISCO)*， 2010-08-09 Update
• GB 3836.2 Explosive atmospheres.Part 2:Equipment protection by flameproof enclosures "d"*， 2010-08-09 Update
• GB 3836.20 Explosive atmospheres.Part 20:Equipment with equipment protection level(EPL)Ga*， 2010-11-10 Update
• GB 3836.3 Explosive atmospheres.Part 3:Equipment protection by increased safety "e"*， 2010-08-09 Update
• GB 3836.4 Explosive atmospheres.Part 4:Equipment protection by intrinsic safety "i"*， 2010-08-09 Update
• GB 3836.5 Electrical apparatus for explosive gas atmosphere-Part 5:Pressurized enclosures"p"
• GB 3836.6 Electrical apparatus for explosive gas atmospheres-Part 6:Oil-immersion"o"
• GB 3836.7 Electrical apparatus for explosive gas atmospheres-Part 7:Power filling"q"
• GB 3836.8 Explosive atmospheres.Part 8: Equipment protection by type of protection “n”*， 2014-12-05 Update
• GB 3836.9 Explosive atmospheres.Part 9:Equipment protection by type of protection "m"*， 2014-12-05 Update
• GB 50093-2002 Code for construction and acceptance of automation instrumentation engineering
• GB 50168-2006 Code for construction and acceptance of cable system electric equipment installation engineering
• GB 5080.1 General Requirements for Equipment Reliability Test
• GB 5080.2 Equipment reliability testing Guidance for the design of test cycles
• GB 5080.4 Point estimation and interval estimation method (exponential distribution) of equipment reliability test reliability determination test
• GB 5080.5 Verification test plan for success rate of equipment reliability test
• GB 5080.7 The verification test plan of failure rate and mean time between failures under the assumption of constant failure rate in equipment reliability test
• GB/T 14065-1993 DDZ-III series process electronic control system Safety barrier
• GB/T 17626.1 Electromagnetic compatibility Testing and measurement techniques Overview of immunity test
• GB/T 17626.10 Electromagnetic compatibility—Testing and measurement techniques—Damped oscillatory magnetic field immunity test*， 2017-12-29 Update
• GB/T 17626.11 Electromagnetic Compatibility Testing and Measurement Techniques Part 11: Voltage Dips, Short Interruptions and Voltage Variation Immunity Tests for Equipment with Input Current Less than or Equal to 16 A per Phase*， 2023-05-23 Update
• GB/T 17626.12 Electromagnetic Compatibility Testing and Measurement Techniques Part 12: Ringing Wave Immunity Test*， 2023-03-17 Update
• GB/T 17626.13 Electromagnetic compatibility Testing and measurement techniques Harmonics and interharmonics including mains signalling at a.c. power port, low frequency immunity test
• GB/T 17626.14 Electromagnetic compatibility Testing and measurement techniques Voltage fluctuation immunity test
• GB/T 17626.15 Electromagnetic compatibility.Testing and measurement techniques .Flickermeter.Functional and design specifications *， 2011-12-30 Update
• GB/T 17626.16 Electromagnetic compatibility Testing and measurement techniques Test for immunity to conducted, common mode disturbances in the frequency range 0 Hz to 150 kHz
• GB/T 17626.17 Electromagnetic compatibility Testing and measurement techniques Ripple on d.c.input power port immunity test
• GB/T 17626.18 Electromagnetic compatibility—Testing and measurement techniques—Damped oscillatory wave immunity test*， 2016-12-13 Update
• GB/T 17626.19 Electromagnetic compatibility—Testing and measurement techniques—Part 19: Test for immunity to conducted, differential mode disturbances and signalling in the frequency range 2 kHz to 150 kHz at a.c.*， 2022-12-30 Update
• GB/T 17626.2 Electromagnetic compatibility.Testing and measurement techniques.Electrostatic discharge immunity test*， 2018-06-07 Update
• GB/T 17626.20 Electromagnetic compatibility.Testing and measurement techniques.Emission and immunity testing in transverse electromagnetic (TEM) waveguide*， 2014-12-22 Update
• GB/T 17626.21 Electromagnetic compatibility.Testing and measurement techniques.Reverberation chamber test methods*， 2014-12-22 Update
• GB/T 17626.22 Electromagnetic compatibility (EMC)—Testing and measurement techniques—Radiated emissions and immunity measurements in fully anechoic rooms（FARs）*， 2017-12-29 Update
• GB/T 17626.24 Electromagnetic compatibility.Testing and measurement techniques.Test methods for protective devices for HEMP conducted disturbance*， 2012-11-05 Update
• GB/T 17626.27 Electromagnetic compatibility Testing and measurement techniques Unbalance immunity test
• GB/T 17626.28 Electromagnetic compatibility Testing and measurement techniques Variation of power frequency, immunity test
• GB/T 17626.29 Electromagnetic compatibility Testing and measurement techniques Voltage dips， short interruptions and voltage variations on d.c.input power port immunity tests
• GB/T 17626.3 Electromagnetic compatibility test and measurement technology Part 3: Radio frequency electromagnetic field radiation immunity test*， 2023-12-28 Update
• GB/T 17626.30 Electromagnetic compatibility test and measurement technology Part 30: Power quality measurement methods*， 2023-12-28 Update
• GB/T 17626.31 Electromagnetic compatibility—Testing and measurement techniques—Part 31：AC mains ports broadband conducted disturbance immunity test*， 2021-12-31 Update
• GB/T 17626.34 Electromagnetic compatibility.Testing and measurement techniques.Voltage dips,short interruptions and voltage variations immunity tests for equipment with mains current more than 16A per phase*， 2012-06-29 Update
• GB/T 17626.4 Electromagnetic compatibility－Testing and measurement techniques－Electrical fast transient/burst immunity test*， 2018-06-07 Update
• GB/T 17626.5 Electromagnetic compatibility—Testing and measurement techniques－Surge immunity test*， 2019-06-04 Update
• GB/T 17626.6 Electromagnetic compatibility—Testing and measurement techniques—Immunity to conducted disturbances,induced by radio-frequency fields*， 2017-12-29 Update
• GB/T 17626.7 Electromagnetic compatibility—Testing and measurement techniques—General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto*， 2017-07-12 Update
• GB/T 17626.8 Electromagnetic compatibility Testing and measurement techniques Power frequency magnetic field immunity test
• GB/T 17626.9 Electromagnetic compatibility. Testing and measurement techniques. Pulse magnetic field immunity test *， 2011-12-30 Update
• GB/T 50311-2000 Code for engineering design of generic cabling system for building and campus
• GB/T 7260 Uninterruptible power systems
• GB/T 7665-2005 General terminology for transducers
• HG/T 20513-2000 Design code for instrument grounding

AQ 9003.1-2008 history

• 2008 AQ 9003.1-2008 Technical specifications for production safety monitoring systems based on network.Part 1: Technical specifications for the connecting of monitoring systems based on network in hazardous area