DIN EN ISO 15103-2:2007
Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007); English version of DIN EN ISO 15103-2:2007-09

Standard No.

DIN EN ISO 15103-2:2007

Release Date

2007

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN ISO 20557-2:2018

Latest

DIN EN ISO 20557-2:2018

Replace

DIN EN ISO 15103-2:2006 DIN EN ISO 15103-2:2004

Scope

This part of ISO 15103 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of poly(phenylene ether) moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given here. Procedures and conditions are described for the preparation of test specimens, and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize poly(phenylene ether) moulding and extrusion materials are listed. The properties have been selected from the general test methods in ISO 10350-1:1998. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this part of ISO 15103, as are the designatory properties specified in ISO 15103-1. In order to obtain reproducible and comparable test results, it is necessary to use the methods of specimen preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

DIN EN ISO 15103-2:2007 Referenced Document

• IEC 60093 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
• IEC 60112 Method for the determination of the proof and the comparative tracking indices of solid insulating materials*， 2020-10-28 Update
• IEC 60243-1 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies*， 2013-03-01 Update
• IEC 60250 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
• IEC 60296 Fluids for electrotechnical applications – Mineral insulating oils for electrical equipment*， 2020-06-26 Update
• ISO 10350-1:1998 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
• ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics; Technical Corrigendum 1
• ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization*， 2018-03-01 Update
• ISO 11359-2:1999 Plastics - Thermomechanical analysis (TMA) - Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
• ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method*， 2019-02-28 Update
• ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*， 2019-02-28 Update
• ISO 1183-3 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
• ISO 15103-1 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 1: Designation system and basis for specifications
• ISO 15512 Plastics — Determination of water content*， 2019-04-30 Update
• ISO 178 Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers*， 2019-04-01 Update
• ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*， 2023-06-07 Update
• ISO 180 Plastics. Determination of Izod impact strength*， 2023-06-07 Update
• ISO 294-1 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens*， 2017-05-01 Update
• ISO 3167 Plastics - Multipurpose test specimens*， 2014-08-01 Update
• ISO 3451-1 Plastics — Determination of ash — Part 1: General methods*， 2019-02-06 Update
• ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics*， 2012-02-01 Update
• ISO 62 Plastics - Determination of water absorption*， 2008-02-01 Update
• ISO 75-2 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite*， 2013-04-01 Update
• ISO 8256 Plastics*， 2023-11-01 Update

DIN EN ISO 15103-2:2007 history

• 2018 DIN EN ISO 20557-2:2018 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties (ISO 20557-2:2018); German version EN ISO 20557-2:2018
• 2007 DIN EN ISO 15103-2:2007 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007); English version of DIN EN ISO 15103-2:2007-09
• 0000 DIN EN ISO 15103-2:2006
• 0000 DIN EN ISO 15103-2:2004

DIN EN ISO 15103-2:2007 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007); English version of DIN EN ISO 15103-2:2007-09 was changed to DIN EN ISO 20557-2:2018 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimen and determination of properties (ISO 20557-2:2018); German version EN ISO 20557-2:2018.