ASTM E3193-21
Standard Test Method for Measurement of Lead (Pb) in Dust by Wipe, Paint, and Soil by Flame Atomic Absorption Spectrophotometry (FAAS)

Standard No.

ASTM E3193-21

Release Date

2021

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM E3193-23

Latest

ASTM E3193-23

Scope

1.1 This test method covers the determination of lead (Pb) in dust by wipe, paint, and soil collected in and around buildings and related structures by flame atomic absorption spectrophotometry (FAAS) and is derived from Test Methods D4185 and E1613. For determination of lead (Pb) and other metals in air by FAAS, see Test Method D4185. 1.2 The sensitivity, detection limit, and optimum working concentration for lead (Pb) are given in Table 1. 1.3 The values stated in SI units are to be regarded as standard. No other values of measurement are included in this standard. 1.3.1 Exception—The SI and inch-pound units shown for wipe sampling data are to be individually regarded as standard for wipe sampling data (14.4.1). 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM E3193-21 Referenced Document

• ASTM D1193 Standard Specification for Reagent Water
• ASTM D1356 Standard Terminology Relating to Sampling and Analysis of Atmospheres*， 2024-04-20 Update
• ASTM D4185 Standard Practice for Measurement of Metals in Workplace Atmosphere by Flame Atomic Absorption Spectrophotometry
• ASTM D4210 Standard Practice for Intralaboratory Quality Control Procedures and a Discussion on Reporting Low-Level Data
• ASTM D4697 Standard Guide for Maintaining Test Methods in the User's Laboratory
• ASTM D4840 Standard Guide for Sample Chain-of-Custody Procedures
• ASTM D6785 Standard Test Method for Determination of Lead in Workplace Air Using Flame or Graphite Furnace Atomic Absorption Spectrometry
• ASTM D6966 Standard Practice for Collection of Settled Dust Samples Using Wipe Sampling Methods for Subsequent Determination of Metals
• ASTM D7035 Standard Test Method for Determination of Metals and Metalloids in Airborne Particulate Matter by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
• ASTM E1188 Standard Practice for Collection and Preservation of Information and Physical Items by a Technical Investigator
• ASTM E1583 Practice for Evaluating Laboratories Engaged in the Determination of Lead in Paint, Dust, Airborne Particulates, and Soil Taken From and Around Buildings and Related Structures
• ASTM E1605 Standard Terminology Relating to Lead in Buildings*， 2022-11-01 Update
• ASTM E1613 Standard Test Method for Determination of Lead by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES), Flame Atomic Absorption Spectrometry (FAAS), or Graphite Furnace Atomic Absorption Spectrometry (GFAAS) Techniques
• ASTM E1644 Standard Practice for Hot Plate Digestion of Dust Wipe Samples for the Determination of Lead
• ASTM E1645 Standard Practice for the Preparation of Dried Paint Samples by Hotplate or Microwave Digestion for Subsequent Lead Analysis
• ASTM E1726 Standard Practice for Preparation of Soil Samples by Hotplate Digestion for Subsequent Lead Analysis
• ASTM E1727 Standard Practice for Field Collection of Soil Samples for Lead Determination by Atomic Spectrometry Techniques
• ASTM E1728 Standard Practice for Field Collection of Settled Dust Samples Using Wipe Sampling Methods for Lead Determination by Atomic Spectrometry Techniques
• ASTM E1729 Standard Practice for Field Collection of Dried Paint Samples for Lead Determination by Atomic Spectrometry Techniques
• ASTM E1741 Standard Practice for Preparation of Airborne Particulate Lead Samples Collected During Abatement and Construction Activities for Subsequent Analysis by Atomic Spectrometry *， 2024-04-20 Update
• ASTM E1792 Standard Specification for Wipe Sampling Materials for Lead in Surface Dust
• ASTM E1864 Standard Practice for Evaluating Quality Systems of Organizations Conducting Facility and Hazard Assessments for Lead in Paint, Dust, Airborne Particulate, and Soil in and around Buildings and Related Structures
• ASTM E1908 Standard Guide for Sample Selection of Debris waste from a Building Renovation or Lead Abatement Project for Toxicity Characteristic Leaching Procedure (TCLP) testing for Leachable Lead (Pb)
• ASTM E1979 Standard Practice for Ultrasonic Extraction of Paint, Dust, Soil, and Air Samples for Subsequent Determination of Lead
• ASTM E2115 Standard Guide for Conducting Lead Hazard Assessments of Dwellings and of Other Child-Occupied Facilities*， 2022-11-01 Update
• ASTM E2239 Standard Practice for Record Keeping and Record Preservation for Lead Hazard Activities*， 2024-03-01 Update
• ASTM E2271/E2271M Standard Practice for Clearance Examinations Following Lead Hazard Reduction Activities in Multifamily Dwellings*， 2022-03-01 Update
• ASTM E2913/E2913M Standard Practice for Hotplate Digestion of Lead from Composited Wipe Samples
• ASTM E2914/E2914M Standard Practice for Ultrasonic Extraction of Lead from Composited Wipe Samples
• ASTM E3074/E3074M Standard Practice for Clearance Examinations Following Lead Hazard Reduction Activities in Single Family Dwellings, in Individual Units of Multifamily Dwellings, and in Other Child-Occupied Facilities*， 2024-04-01 Update
• ASTM E456 Standard Terminology for Relating to Quality and Statistics
• ASTM E631 Standard Terminology of Building Constructions
• ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
• ISO/IEC 17025 General requirements for the competence of testing and calibration laboratories [Standard in French]

ASTM E3193-21 history

• 2023 ASTM E3193-23 Standard Test Method for Measurement of Lead (Pb) by Flame Atomic Absorption Spectrophotometry (FAAS)
• 2021 ASTM E3193-21 Standard Test Method for Measurement of Lead (Pb) in Dust by Wipe, Paint, and Soil by Flame Atomic Absorption Spectrophotometry (FAAS)
• 2020 ASTM E3193-20 Standard Test Method for Measurement of Lead (Pb) in Dust by Wipe, Paint, and Soil by Flame Atomic Absorption Spectrophotometry (FAAS)
• 2019 ASTM E3193-19 Standard Test Method for Measurement of Lead (Pb) in Dust by Wipe, Paint, and Soil by Flame Atomic Absorption Spectrophotometry (FAAS)