ASTM C1109-10(2015)
Standard Practice for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectroscopy

Standard No.

ASTM C1109-10(2015)

Release Date

2010

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM C1109-23

Latest

ASTM C1109-23

Scope

5.1 This practice may be used to determine concentrations of elements leached from nuclear waste materials (glasses, ceramics, cements) using an aqueous leachant. If the nuclear waste material is radioactive, a suitably contained and shielded ICP-AES spectrometer system with a filtered exit-gas system must be used, but no other changes in the practice are required. The leachant may be deionized water or any aqueous solution containing less than 18201;% total solids.

5.2 This practice as written is for the analysis of solutions containing 18201;% (v/v) nitric acid. It can be modified to specify the use of the same or another mineral acid at the same or higher concentration. In such cases, the only change needed in this practice is to substitute the preferred acid and concentration value whenever 18201;% nitric acid appears here. It is important that the acid type and content of the reference and check solutions closely match the leachate solutions to be analyzed.

5.3 This practice can be used to analyze leachates from static leach testing of waste forms using Test Method C1220.

1.1 This practice is applicable to the determination of low concentration and trace elements in aqueous leachate solutions produced by the leaching of nuclear waste materials, using inductively coupled plasma-atomic emission spectroscopy (ICP-AES).

1.2 The nuclear waste material may be a simulated (non-radioactive) solid waste form or an actual solid radioactive waste material.

1.3 The leachate may be deionized water or any natural or simulated leachate solution containing less than 18201;% total dissolved solids.

1.4 This practice should be used by analysts experienced in the use of ICP-AES, the interpretation of spectral and non-spectral interferences, and procedures for their correction.

1.5 No detailed operating instructions are provided because of differences among various makes and models of suitable ICP-AES instruments. Instead, the analyst shall follow the instructions provided by the manufacturer of the particular instrument. This test method does not address comparative accuracy of different devices or the precision between instruments of the same make and model.

1.6 This practice contains notes that are explanatory and are not part of the mandatory requirements of the method.

1.7 The values stated in SI units are to be regarded as the standard.

1.8 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1109-10(2015) Referenced Document

• ASTM C1009 Standard Guide for Establishing a Quality Assurance Program for Analytical Chemistry Laboratories Within the Nuclear Industry
• ASTM C1220 Standard Test Method for Static Leaching of Monolithic Waste Forms for Disposal of Radioactive Waste
• ASTM C859 Standard Terminology Relating to Nuclear Materials
• ASTM D1193 Standard Specification for Reagent Water
• ASTM D7035 Standard Test Method for Determination of Metals and Metalloids in Airborne Particulate Matter by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
• ASTM E135 Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials
• ASTM E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
• ISO 1042 Laboratory glassware - One-mark volumetric flasks
• ISO 3585 Borosilicate glass 3.3 - Properties
• ISO 8655 Piston-operated volumetric apparatus — Part 9: Manually operated precision laboratory syringes

ASTM C1109-10(2015) history

• 2024 ASTM C1109-23 Standard Practice for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectroscopy
• 2010 ASTM C1109-10(2015) Standard Practice for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectroscopy
• 2010 ASTM C1109-10 Standard Practice for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectrometry
• 2004 ASTM C1109-04 Standard Practice for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectrometry
• 1998 ASTM C1109-98 Standard Test Method for Analysis of Aqueous Leachates from Nuclear Waste Materials Using Inductively Coupled Plasma-Atomic Emission Spectrometry