ASTM E2104-15
Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components

Standard No.

ASTM E2104-15

Release Date

2015

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM E2104-22

Latest

ASTM E2104-22

Scope

4.1 The requirements for radiographic examination in this practice are applicable to all types of metallic and nonmetallic material used in designated applications such as gas turbines and flight structures.

4.2 This practice establishes the basic parameters for the application and control of the radiographic process. This practice may be specified on an engineering drawing, specification or contract; however, it is not a detailed radiographic technique and must be supplemented. Section 7 and Test Methods E1030 and E1032 contain information to help develop detailed radiographic techniques.

1.1 This practice establishes the minimum requirements for radiographic examination of metallic and nonmetallic materials and components used in designated applications such as gas turbine engines and flight structures.

1.2 The requirements in this practice are intended to control the radiographic process to ensure the quality of radiographic images produced for use in designated applications such as gas turbine engines and flight structures; this practice is not intended to establish acceptance criteria for material or components. When examination is performed in accordance with this practice, engineering drawings, specifications or other applicable documents shall indicate the acceptance criteria.

1.3 All areas of this practice may be open to agreement between the cognizant engineering organization and the supplier, or specific direction from the cognizant engineering organization.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM E2104-15 Referenced Document

• ANSI/AWS A2.4 Standard Symbols for Welding@ Brazing@ and Nondestructive Examination (7th Edition)
• ASTM E1025 Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiology
• ASTM E1030 Standard Test Method for Radiographic Examination of Metallic Castings
• ASTM E1032 Standard Test Method for Radiographic Examination of Weldments
• ASTM E1079 Standard Practice for Calibration of Transmission Densitometers
• ASTM E1165 Standard Test Method for Measurement of Focal Spots of Industrial X-Ray Tubes by Pinhole Imaging
• ASTM E1254 Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
• ASTM E1316 Standard Terminology for Nondestructive Examinations
• ASTM E1390 Standard Guide for Illuminators Used for Viewing Industrial Radiographs
• ASTM E1815 Standard Test Method for Classification of Film Systems for Industrial Radiography
• ASTM E1817 Standard Practice for Controlling Quality of Radiological Examination by Using Representative Quality Indicators (RQIs)
• ASTM E2033 Standard Practice for Computed Radiology (Photostimulable Luminescence Method)
• ASTM E2698 Standard Practice for Radiographic Examination Using Digital Detector Arrays
• ASTM E543 Standard Practice for Agencies Performing Nondestructive Testing
• ASTM E747 Standard Practice for Design, Manufacture and Material Grouping Classification of Wire Image Quality Indicators (IQI) Used for Radiology
• ASTM E999 Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing

ASTM E2104-15 history

• 2022 ASTM E2104-22 Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components
• 2015 ASTM E2104-15 Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components
• 2009 ASTM E2104-09 Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components
• 2001 ASTM E2104-01 Standard Practice for Radiographic Examination of Advanced Aero and Turbine Materials and Components