ASTM B745/B745M-15
Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains

Standard No.
ASTM B745/B745M-15
Release Date
2015
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM B745/B745M-15(2021)
Latest
ASTM B745/B745M-15(2021)
Scope

1.1 This specification covers corrugated aluminum pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes.

1.2 This specification does not include requirements for bedding, backfill, or the relationship between earth-cover load and sheet thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the sheet thickness. The structural design of corrugated aluminum pipe and the proper installation procedures are given in Practices B790/B790M and B788/B788M, respectively. A procedure for using life-cycle cost analysis techniques to evaluate alternative drainage system designs using corrugated metal pipe is given in Practice A930.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM B745/B745M-15 Referenced Document

  • ASTM A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
  • ASTM A307 Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strangth
  • ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts
  • ASTM A563M Standard Specification for Carbon and Alloy Steel Nuts 40;Metric41;
  • ASTM A796/A796M Standard Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications
  • ASTM A930 Standard Practice for Life-Cycle Cost Analysis of Corrugated Metal Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits
  • ASTM B209 Standard Specification for Aluminum and Aluminum- Alloy Sheet and Plate
  • ASTM B209M Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)
  • ASTM B221 Standard Specification for Aluminum-Alloy Extruded Bars, Rods, Wire, Shapes, and Tubes
  • ASTM B221M Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)
  • ASTM B316/B316M Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods
  • ASTM B633 Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
  • ASTM B666/B666M Standard Practice for Identification Marking of Aluminum and Magnesium Products
  • ASTM B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
  • ASTM B744/B744M Standard Specification for Aluminum Alloy Sheet for Corrugated Aluminum Pipe
  • ASTM B788/B788M Standard Practice for Installing Factory-Made Corrugated Aluminum Culverts and Storm Sewer Pipe
  • ASTM B790/B790M Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
  • ASTM C443 Standard Specification for Joints for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets
  • ASTM D1056 Standard Specification for Sponge and Expanded Cellular Rubber Products
  • ASTM F467 Standard Specification for Nonferrous Nuts for General Use
  • ASTM F467M Standard Specification for Nonferrous Nuts for General Use [Metric]
  • ASTM F468 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
  • ASTM F468M Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
  • ASTM F568M Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners
  • ASTM F593 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
  • ASTM F594 Standard Specification for Stainless Steel Nuts
  • ASTM F738M Standard Specification for Stainless Steel Metric Bolts, Screws, and Studs
  • ASTM F836M Standard Specification for Style 1 Stainless Steel Metric Nuts

ASTM B745/B745M-15 history

Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains


Copyright ©2024 All Rights Reserved