ASTM D2000-12(2017)
Standard Classification System for Rubber Products in Automotive Applications
- Standard No.
- ASTM D2000-12(2017)
- Release Date
- 2012
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D2000-18
- Latest
- ASTM D2000-18
- Scope
-
1.1 This classification system covers the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.
Note 1: This classification system may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used.
1.2 This classification system is based on the premise that the properties of all rubber products can be arranged into characteristic material designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling in oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all elastomeric materials.
1.3 In all cases where the provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence.
Note 2: When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance, to establish the appropriate properties, test methods, and specification test limits.
1.4 The values stated in SI units are to be regarded as standard.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D2000-12(2017) Referenced Document
- ASTM D1053 Standard Test Methods for Rubber Property—Stiffening at Low Temperatures: Flexible Polymers and Coated Fabrics
- ASTM D1149 Standard Test Method for Rubber Deterioration-Surface Ozone Cracking in a Chamber
- ASTM D1171 Standard Test Method for Rubber Deteriorationx2014;Surface Ozone Cracking Outdoors or Chamber (Triangular Specimens)
- ASTM D1329 Standard Test Method for Evaluating Rubber Property-Retraction at Lower Temperatures (TR Test)
- ASTM D1349 Standard Practice for Rubber-Standard Temperatures for Testing
- ASTM D1418 Standard Practice for Rubber and Rubber Latices-Nomenclature
- ASTM D2137 Standard Test Methods for Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics
- ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-20 Update
- ASTM D3183 Standard Practice for Rubber-Preparation of Pieces for Test Purposes from Products
- ASTM D395 Standard Test Methods for Rubber Property-Compression Set
- ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers8212;Tension
- ASTM D429 Standard Test Methods for Rubber Property-Adhesion to Rigid Substrates
- ASTM D430 Standard Test Methods for Rubber Deterioration-Dynamic Fatigue
- ASTM D471 Standard Test Method for Rubber Property-Effect of Liquids
- ASTM D573 Standard Test Method for Rubber-Deterioration in an Air Oven
- ASTM D575 Standard Test Methods for Rubber Properties in Compression
- ASTM D5964 Standard Practice for Rubber IRM 902 and IRM 903 Replacement Oils for ASTM No. 2 and ASTM No. 3 Oils
- ASTM D624 Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
- ASTM D865 Standard Test Method for Rubber-Deterioration by Heating in Air (Test Tube Enclosure)
- ASTM D925 Standard Test Methods for Rubber Property-Staining of Surfaces (Contact, Migration, and Diffusion)
- ASTM D945 Standard Test Methods for Rubber Properties in Compression or Shear (Mechanical Oscillograph)
ASTM D2000-12(2017) history
- 2018 ASTM D2000-18 Standard Classification System for Rubber Products in Automotive Applications
- 2012 ASTM D2000-12(2017) Standard Classification System for Rubber Products in Automotive Applications
- 2012 ASTM D2000-12 Standard Classification System for Rubber Products in Automotive Applications
- 2008 ASTM D2000-08 Standard Classification System for Rubber Products in Automotive Applications
- 2006 ASTM D2000-06ae1 Standard Classification System for Rubber Products in Automotive Applications
- 2006 ASTM D2000-06a Standard Classification System for Rubber Products in Automotive Applications
- 2006 ASTM D2000-06e1 Standard Classification System for Rubber Products in Automotive Applications
- 2006 ASTM D2000-06 Standard Classification System for Rubber Products in Automotive Applications
- 2005 ASTM D2000-05 Standard Classification System for Rubber Products in Automotive Applications
- 2004 ASTM D2000-04 Standard Classification System for Rubber Products in Automotive Applications
- 2003 ASTM D2000-03ae1 Standard Classification System for Rubber Products in Automotive Applications
- 2003 ASTM D2000-03a Standard Classification System for Rubber Products in Automotive Applications
- 2003 ASTM D2000-03 Standard Classification System for Rubber Products in Automotive Applications
- 2001 ASTM D2000-01 Standard Classification System for Rubber Products in Automotive Applications
- 2000 ASTM D2000-00e1 Standard Classification System for Rubber Products in Automotive Applications
- 2000 ASTM D2000-00 Standard Classification System for Rubber Products in Automotive Applications
