ASTM F3184-16
Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion

Standard No.

ASTM F3184-16

Release Date

2016

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM F3184-16(2023)

Latest

ASTM F3184-16(2023)

Scope

1.1 This specification covers additive manufacturing of UNS S31603 components by means of laser and electron beam-based full melt powder bed fusion processes. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions.

1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured UNS S31603 components for defining the requirements and ensuring component properties.

1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee.

1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Supplementary Requirements S1–S16.

1.5 The compositional requirements specified in this specification do not meet the compositional requirements for surgical implant grade UNS S31673.

1.6 The values stated in SI units are to be regarded as the standard. Other units are included only for informational purposes.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F3184-16 Referenced Document

• ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay) ( - 2009)
• ASTM A1080 Standard Practice for Hot Isostatic Pressing of Steel, Stainless Steel, and Related Alloy Castings
• ASTM A262 Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
• ASTM A276/A276M Standard Specification for Stainless Steel Bars and Shapes
• ASTM A479/A479M Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
• ASTM A484/A484M Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings
• ASTM A751 Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
• ASTM B213 Standard Test Method for Flow Rate of Metal Powders
• ASTM B214 Standard Test Method for Sieve Analysis of Metal Powders
• ASTM B243 Standard Terminology of Powder Metallurgy
• ASTM B311 Test Method for Density Determination for Powder Metallurgy (P/M) Materials Containing Less Than Two Percent Porosity
• ASTM B769 Standard Test Method for Shear Testing of Aluminum Alloys
• ASTM B855 Standard Test Method for Volumetric Flow Rate of Metal Powders Using Arnold Meter and Hall Funnel
• ASTM B964 Standard Test Methods for Flow Rate of Metal Powders Using the Carney Funnel
• ASTM D3951 Standard Practice for Commercial Packaging
• ASTM E10 Standard Test Method for Brinell Hardness of Metallic Materials
• ASTM E1019 Standard Test Methods for Determination of Carbon, Sulfur, Nitrogen, and Oxygen in Steel and in Iron, Nickel, and Cobalt Alloys*， 2024-04-20 Update
• ASTM E1086 Standard Test Method for Optical Emission Vacuum Spectrometric Analysis of Stainless Steel by the Point-to-Plane Excitation Technique
• ASTM E11 Standard Specification for Wire Cloth and Sieves for Testing Purposes
• ASTM E1417 Standard Practice for Liquid Penetrant Examination
• ASTM E1450 Standard Test Method for Tension Testing of Structural Alloys in Liquid Helium
• ASTM E1479 Standard Practice for Describing and Specifying Inductively-Coupled Plasma Atomic Emission Spectrometers
• ASTM E1742 Standard Practice for Radiographic Examination
• ASTM E18 Standard Test Methods for Rockwell Hardness of Metallic Materials
• ASTM E1820 Standard Test Method for Measurement of Fracture Toughness
• ASTM E21 Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
• ASTM E23 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
• ASTM E2368 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
• ASTM E238 Standard Test Method for Pin-Type Bearing Test of Metallic Materials
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• ASTM E3 Standard Practice for Preparation of Metallographic Specimens
• ASTM E353 Standard Test Methods for Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys
• ASTM E384 Standard Test Method for Microindentation Hardness of Materials
• ASTM E399 Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials
• ASTM E407 Standard Practice for Microetching Metals and Alloys
• ASTM E466 Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials
• ASTM E606 Standard Practice for Strain-Controlled Fatigue Testing
• ASTM E647 Standard Test Method for Measurement of Fatigue Crack Growth Rates
• ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials
• ASTM E9 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
• ASTM F2924 Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion
• ASTM F2971 Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing
• ASTM F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes
• ASTM F3122 Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes
• ISO 1099 Metallic materials - Fatigue testing - Axial force-controlled method
• ISO 12108 Metallic materials - Fatigue testing - Fatigue crack growth method
• ISO 12111 Metallic materials - Fatigue testing - Strain-controlled thermomechanical fatigue testing method
• ISO 12135 Metallic materials - Unified method of test for the determination of quasistatic fracture toughness
• ISO 12737 Metallic materials — Determination of plane-strain fracture toughness
• ISO 13485 
• ISO 148-1 Metallic materials - Charpy pendulum impact test - Part 1: Test method
• ISO 19819 Metallic materials - Tensile testing in liquid helium
• ISO 4545 Metallic materials; hardness test; Knoop test
• ISO 6506-1 Metallic materials - Brinell hardness test - Part 1: Test method
• ISO 6507-1 Metallic materials — Vickers hardness test — Part 1: Test method
• ISO 6508 Metallic materials; Hardness test; Rockwell test (scales A - B - C - D - E - F - G - H - K)
• ISO 6892-1 Metallic materials — Tensile testing — Part 1: Method of test at room temperature
• ISO 6892-2 Metallic materials - Tensile testing- Part 2:Method of test at elevated temperature
• ISO 9001 Quality management systems - Requirements [Spanish version]
• ISO 9044 Industrial woven wire cloth - Technical requirements and tests
• SAE AMS2248 CHEMICAL CHECK ANALYSIS LIMITS Wrought Heat and Corrosion Resistant Steels
• SAE AMS2759 HEAT TREATMENT OF STEEL PARTS General Requirements

ASTM F3184-16 history

• 2023 ASTM F3184-16(2023) Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion
• 2016 ASTM F3184-16 Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion