ASTM D6237-09(2015)
Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
- Standard No.
- ASTM D6237-09(2015)
- Release Date
- 2009
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D6237-19
- Latest
- ASTM D6237-19
- Scope
3.1 This guide is intended as a reference for those concerned with the inspection of thin- or thick-film coating application to concrete and masonry substrates. It does not cover the application of cement-type coatings. A checklist is included as Appendix X1.1. Many of the details covered may be in a specification for a particular project. A specification for coating projects should include the coatings to be used.
1.1 This guide is intended as an information aid to painting inspectors in carrying out the task efficiently. It includes the key elements of surface preparation, coatings application, and final approval for both field and shop work. The items should be selected that are pertinent to a particular job.
Note 1: For additional helpful information, refer to the following documents:
Manual of Concrete Practice ACI 515R American Concrete Institute2
Manual of Coating Work for Light Water Nuclear Power Plant Primary Containment and Other Safety Related Facilities3
C811 Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings4
SSPC-PA Guide 3 - A Guide to Safety in Paint Application5
Steel Structures Painting Manual Vol. 1- Good Painting Practices5
Steel Structures Painting Manual Vol. 2 - Systems and Specifications5
Manufacturers Specifications and Instructions (made available to the inspector for reference to special requirements for proper application)
Material Safety Data Sheets (needed to insure that personnel take necessary precautions in handling hazardous materials). Available from Materials manufacturer.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whomever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This guide is arranged in the following order:
ASTM D6237-09(2015) Referenced Document
- ASTM C811 Standard Practice for Surface Preparation of Concrete for Application of Chemical-Resistant Resin Monolithic Surfacings
- ASTM D1212 Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings
- ASTM D1475 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
- ASTM D3359 Standard Test Methods for Measuring Adhesion by Tape Test
- ASTM D4138 Standard Test Methods for Measurement of Dry Film Thickness of Protective Coating Systems by Destructive Means
- ASTM D4212 Standard Test Method for Viscosity by Dip-Type Viscosity Cups
- ASTM D4258 Standard Practice for Surface Cleaning Concrete for Coating
- ASTM D4259 Standard Practice for Abrading Concrete
- ASTM D4260 Standard Practice for Acid Etching Concrete
- ASTM D4262 Standard Test Method for pH of Chemically Cleaned or Etched Concrete Surfaces
- ASTM D4263 Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method
- ASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed Air
- ASTM D4414 Standard Practice for Measurement of Wet Film Thickness by Notch Gages
- ASTM D4787 Standard Practice for Continuity Verification of Liquid or Sheet Linings Applied to Concrete Substrates
- ASTM D5064 Standard Practice for Conducting a Patch Test to Assess Coating Compatibility
- ASTM D6132 Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Applied Organic Coatings Over Concrete Using an Ultrasonic Gage
- ASTM D6677 Standard Test Method for Evaluating Adhesion by Knife
- ASTM D7234 Standard Test Method for Pull-Off Strength of Coatings on Concrete Using Portable Pull-Off Adhesion Testers
- ASTM E1907 Standard Practices for Determining Moisture-Related Acceptability of Concrete Floors to Receive Moisture-Sensitive Finishes
- ASTM F1869 Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride
- ASTM F2170 Standard Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes
ASTM D6237-09(2015) history
- 2019 ASTM D6237-19 Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
- 2009 ASTM D6237-09(2015) Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
- 2009 ASTM D6237-09 Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
- 2003 ASTM D6237-03 Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
- 1998 ASTM D6237-98 Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
Copyright ©2024 All Rights Reserved