ASTM E1797-12
Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
- Standard No.
- ASTM E1797-12
- Release Date
- 2012
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM E1797-12(2017)e1
- Latest
- ASTM E1797-12(2017)e1
- Scope
1.1 This specification covers minimum material performance requirements and laboratory test procedures for reinforced liquid coating encapsulation products (single- or multiple-coat systems) for leaded paint in buildings. Performance properties addressed in this specification are:
1.1.1 Impact Resistance,
1.1.2 Adhesion,
1.1.3 Dry Abrasion Resistance,
1.1.4 Water Vapor Transmission,
1.1.5 Water and Chemical Resistance,
1.1.6 Surface Burning Characteristics,
1.1.7 Volatile Organic Compound (VOC) Content,
1.1.8 Weathering,
1.1.9 Aging,
1.1.10 Scrub Resistance,
1.1.11 Mildew Resistance,
1.1.12 Paintability/Repairability,
1.2 This specification does not address the selection of an encapsulation product for specific use conditions. Specific use conditions may require performance values other than those stated in this specification. See Guide E1796 for guidance.
1.3 This specification complements Specification E1795 for non-reinforced liquid coating encapsulation products.
1.4 This specification does not cover the use of encapsulation products on industrial steel structures nor residential exterior coated metal surfaces because no corrosion control requirements are included.
1.5 This specification applies to any liquid-applied product incorporating reinforcement materials as part of the system. Reinforcement materials are continuous fabric or mesh and are applied in the field. These materials are typically applied between a base and top coat. These products are used to encapsulate a leaded paint surface with the intent of reducing human exposure to lead in paint.
1.6 The results of the test methods included in this specification will not necessarily predict field performance.
1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM E1797-12 Referenced Document
- ASTM D1005 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
- ASTM D1212 Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings
- ASTM D1308 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
- ASTM D1475 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
- ASTM D16 Standard Terminology for Paint, Related Coatings, Materials, and Applications
- ASTM D1653 Standard Test Methods for Water Vapor Transmission of Organic Coating Films
- ASTM D2486 Standard Test Methods for Scrub Resistance of Wall Paints*， 2024-04-20 Update
- ASTM D2794 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
- ASTM D3273 Standard Test Method for Resistance to Growth of Moid on the Surface of Interior Coatings in an Enviormental Chamber
- ASTM D3274 Standard Test Method for Evaluating Degree of Surface Disfigurement of Paint Films by Microbial (Fungal or Algal) Growth or Soil and Dirt Accumulation
- ASTM D3359 Standard Test Methods for Measuring Adhesion by Tape Test
- ASTM D3891 Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products
- ASTM D3924 Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials
- ASTM D3925 Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings
- ASTM D3960 Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
- ASTM D4060 Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
- ASTM D4214 Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films
- ASTM D4414 Standard Practice for Measurement of Wet Film Thickness by Notch Gages
- ASTM D4541 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
- ASTM D7091 Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
- ASTM D823 Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels
- ASTM E1605 Standard Terminology Relating to Lead in Buildings
- ASTM E1795 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
- ASTM E1796 Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings
- ASTM E2239 Standard Practice for Record Keeping and Record Preservation for Lead Hazard Activities
- ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
- ASTM G154 Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials
ASTM E1797-12 history
- 2017 ASTM E1797-12(2017)e1 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
- 2012 ASTM E1797-12 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
- 2004 ASTM E1797-04 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
- 2003 ASTM E1797-03 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
- 2000 ASTM E1797-00 Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
