1.1 This specification covers minimum material performance requirements and laboratory test procedures for nonreinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings. Performance properties addressed in this specification are:
1.1.1 Impact resistance,
1.1.2 Adhesion,
1.1.3 Dry abrasion resistance,
1.1.4 Water vapor transmission,
1.1.5 Water and chemical resistance,
1.1.6 Surface burning characteristics,
1.1.7 Volatile organic compound (VOC) content,
1.1.8 Weathering,
1.1.9 Aging,
1.1.10 Scrub resistance,
1.1.11 Mildew resistance,
1.1.12 Paintability/repairability,
1.1.13 Flexibility, and
1.1.14 Tensile properties.
1.2 This specification does not address the selection of an encapsulation product for specific use conditions. Specific use conditions may require performance values other than those stated in this specification. See Guide E1796.
1.3 This specification does not cover the use of corrosioninhibiting primers prior to encapsulation products on either industrial steel structures or on residential coated metal surfaces. Types of Direct-To-Metal (DTM) primers in conjunction with lead paint encapsulants has not been investigated. Use of primers to yield substrates acceptable to receive an encapsulant, and to inhibit future corrosion of encapsulated substrates, should be evaluated by trial applications at each specific project.
1.4 This specification applies to any non-reinforced liquid applied product that relies primarily on adhesion for attachment to the surface. These products are used to encapsulate a leaded paint surface with the intent of reducing human exposure to lead.
1.5 The results of the test methods included in this specification will not necessarily predict field performance.
1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E1795-20a Referenced Document
ASTM D1005 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
ASTM D1193 Standard Specification for Reagent Water
ASTM D1212 Standard Test Methods for Measurement of Wet Film Thickness of Organic Coatings
ASTM D1308 Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes
ASTM D1356 Standard Terminology Relating to Sampling and Analysis of Atmospheres*, 2024-04-22 Update
ASTM D1475 Standard Test Method For Density of Liquid Coatings, Inks, and Related Products
ASTM D16 Standard Terminology for Paint, Related Coatings, Materials, and Applications
ASTM D1653 Standard Test Methods for Water Vapor Transmission of Organic Coating Films
ASTM D2370 Standard Test Method for Tensile Properties of Organic Coatings
ASTM D2486 Standard Test Methods for Scrub Resistance of Wall Paints*, 2024-04-22 Update
ASTM D2794 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)*, 2024-01-25 Update
ASTM D3273 Standard Test Method for Resistance to Growth of Moid on the Surface of Interior Coatings in an Enviormental Chamber
ASTM D3274 Standard Test Method for Evaluating Degree of Surface Disfigurement of Paint Films by Microbial (Fungal or Algal) Growth or Soil and Dirt Accumulation
ASTM D3359 Standard Test Methods for Measuring Adhesion by Tape Test
ASTM D3891 Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products
ASTM D3924 Standard Specification for Standard Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials
ASTM D3925 Standard Practice for Sampling Liquid Paints and Related Pigmented Coatings
ASTM D3960 Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
ASTM D4060 Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D4214 Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films
ASTM D4414 Standard Practice for Measurement of Wet Film Thickness by Notch Gages
ASTM D4708 Standard Practice for Preparation of Uniform Free Films of Organic Coatings
ASTM D522/D522M Standard Test Methods for Mandrel Bend Test of Attached Organic Coatings*, 2021-11-01 Update
ASTM D7091 Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals*, 2022-06-01 Update
ASTM D823 Standard Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels
ASTM E1605 Standard Terminology Relating to Lead in Buildings*, 2022-11-01 Update
ASTM E1796 Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings
ASTM E2239 Standard Practice for Record Keeping and Record Preservation for Lead Hazard Activities*, 2024-03-01 Update
ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
ASTM G154 Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials*, 2023-01-01 Update
ASTM E1795-20a history
2020ASTM E1795-20a Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
2020ASTM E1795-20 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
2017ASTM E1795-17 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
2012ASTM E1795-12 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
2004ASTM E1795-04 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
2000ASTM E1795-00 Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings