ASTM F2363/F2363M-12
Standard Specification for Sewage and Graywater Flow Through Treatment Systems

Standard No.

ASTM F2363/F2363M-12

Release Date

2012

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM F2363/F2363M-17

Latest

ASTM F2363/F2363M-17(2023)

Scope

1.1 This specification covers the design, manufacture, performance, operation, and testing of flow through treatment systems intended to process sewage or graywater, or both, generated during a ship''s normal service. This specification is intended for use by designers, manufacturers, purchasers, and operators of shipboard environmental pollution control equipment to determine the requirements for equipment design, manufacture, purchase, and in-service operation.

1.2 The treatment system shall be capable of meeting the effluent requirements detailed in Section 4 with respect to a ship''s operational area.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

9.1 This test method uses performance-based quantitative procedures for evaluation, inspection, and testing of sewage or graywater flow through treatment systems.

ASTM F2363/F2363M-12 Referenced Document

• ANSI/ASSE 1001 Performance Requirements for Atmospheric Type Vacuum Breakers
• ANSI/ASSE 1013 Performance Requirements for Reduced Pressure Principle Backflow Prevention Assemblies
• ANSI/ISA 60079-1 Explosive Atmospheres - Part 1: Equipment Protection by Flameproof Enclosures “d”
• ANSI/NEMA 250 Enclosures for Electrical Equipment (1,000 Volts Maximum)
• ANSI/NEMA MG 1 
• ASTM A307 Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strangth
• ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts*， 2024-04-19 Update
• ASTM B117 Standard Practice for Operating Salt Spray (Fog) Apparatus
• ASTM B165 Standard Specification for Nickel-Copper Alloy (UNS N04400)* Seamless Pipe and Tube
• ASTM D1253 Standard Test Method for Residual Chlorine in Water
• ASTM E11 Standard Specification for Wire Cloth and Sieves for Testing Purposes
• ASTM F1030 Standard Practice for Selection of Valve Operators
• ASTM F1098 Standard Specification for Envelope Dimensions for Butterfly Valves—NPS 2 to 24
• ASTM F1122 Standard Specification for Quick Disconnect Couplings
• ASTM F1155 Standard Practice for Selection and Application of Piping System Materials
• ASTM F1166 Standard Practice for Human Engineering Design for Marine Systems, Equipment and Facilities
• ASTM F1298 Standard Specification for Flexible, Expansion-Type Ball Joints for Marine Applications
• ASTM F1323 Standard Specification for Shipboard Incinerators
• ASTM F1387 Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• ASTM F1510 Standard Specification for Rotary Positive Displacement Pumps, Commercial Ships Use
• ASTM F1511 Standard Specification for Mechanical Seals for Shipboard Pump Applications
• ASTM F2044 Standard Specification for Liquid Level Indicating Equipment, Electrical
• ASTM F906 Standard Specification for Letters and Numerals for Ships
• ASTM F992 Standard Specification for Valve Label Plates
• ASTM F993 Standard Specification for Valve Locking Devices
• ASTM F998 Standard Specification for Centrifugal Pump, Shipboard Use
• IEEE 1580 IEEE Recommended Practice for Marine Cable for Use on Shipboard and Fixed or Floating Facilities
• ISO 15705 Water quality - Determination of the chemical oxygen demand index (ST-COD) - Small-scale sealed-tube method
• ISO 5815-1 Water quality — Determination of biochemical oxygen demand after n days (BODn) — Part 1: Dilution and seeding method with allylthiourea addition

ASTM F2363/F2363M-12 history

• 2023 ASTM F2363/F2363M-17(2023) Standard Specification for Sewage and Graywater Flow Through Treatment Systems
• 2017 ASTM F2363/F2363M-17 Standard Specification for Sewage and Graywater Flow Through Treatment Systems
• 2012 ASTM F2363/F2363M-12 Standard Specification for Sewage and Graywater Flow Through Treatment Systems
• 2006 ASTM F2363-06 Standard Specification for United States Coast Guard Type II or IMO MARPOL 73/78 Annex IV Marine Sanitation Devices (Flow Through Treatment)
• 2004 ASTM F2363-04 Standard Specification for United States Coast Guard Type II or IMO MARPOL 73/78 Annex IV Marine Sanitation Devices (Flow Through Treatment)