DIN EN 12201-1:2011
This part of EN 12201 specifies the general aspects of poyethylene (PE) - pressure piping systems (mains and service pipes)for buried or above ground applications. intended for the conveyance of water for human consumption,raw water prior to treatment, dr
- Standard No.
- DIN EN 12201-1:2011
- Release Date
- 2011
- Published By
- German Institute for Standardization
- Status
- Replace By
- DIN EN 12201-1:2011-11
- Latest
- DIN EN 12201-1:2021-05
- Replace
- DIN EN 12201-1:2003 DIN EN 12201-1:2010 DIN EN 13244-1:2003
DIN EN 12201-1:2011 Referenced Document
- EN 12099 Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
- EN 12201-2:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes (Incorporates Amendment A1: 2013)
- EN ISO 1043-1:2001 Plastics - Symbols and Abbreviated Terms - Part 1: Basic Polymers and Their Special Characteristics
- EN ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
- EN ISO 1167-1 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
- EN ISO 1167-2 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
- EN ISO 1183-1 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pycnometer method and titration method (ISO 1183-1:2019, Corrected version 2019-05)*， 2019-04-03 Update
- EN ISO 1183-2 Plastics - Methods for determining the density of noncellular plastics - Part 2: Density gradient column method*， 2019-04-01 Update
- EN ISO 12162 Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162:2009)
- EN ISO 13477 Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008)
- EN ISO 13478 Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007)
- EN ISO 13479 Polyolefin pipes for the conveyance of fluids - Determination of resistance to crack propagation - Test method for slow crack growth on notched pipes (ISO 13479:2022)*， 2022-06-15 Update
- EN ISO 15512 Plastics - Determination of water content (ISO 15512:2019)*， 2019-05-29 Update
- EN ISO 16871 Plastics piping and ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering Supersedes EN 1056:1996; ISO 16871:2003
- EN ISO 472:2001 Plastics - Vocabulary
- EN ISO 6259-1 Thermoplastics pipes - Determination of tensile properties - Part 1: General test method*， 2015-04-01 Update
- ISO 6259-3 Thermoplastics pipes - Determination of tensile properties - Part 3: Polyolefin pipes*， 2015-06-01 Update
- ISO 69 Cinematography - 16 mm motion-picture and magnetic film - Cutting and perforating dimensions
DIN EN 12201-1:2011 history
- 2021 DIN EN 12201-1:2021-05 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General; German and English version prEN 12201-1:2021 / Note: Date of issue 2021-04-02*Intended as replacement for DIN EN 12201-1 (2011...
- 2011 DIN EN 12201-1:2011-11 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General; German version EN 12201-1:2011 / Note: To be replaced by DIN EN 12201-1 (2021-05).
- 2011 DIN EN 12201-1:2011 This part of EN 12201 specifies the general aspects of poyethylene (PE) - pressure piping systems (mains and service pipes)for buried or above ground applications. intended for the conveyance of water for human consumption,raw water prior to treatment, dr
- 2003 DIN EN 12201-1:2003 Plastic piping systems for water supply Polyethylene (PE) Part 1: General
- 1970 DIN EN 12201-1 E:1996-02
