DIN EN 12201-5:2011
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system; German version EN 12201-5:2011

Standard No.

DIN EN 12201-5:2011

Release Date

2011

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN 14511-4:2013

DIN EN 12201-5:2011-11

Latest

DIN EN 12201-5:2021-05

Replace

DIN EN 12201-5:2003 DIN EN 12201-5:2010 DIN EN 13244-5:2003 DIN EN 13244-5 Berichtigung 1:2003

Scope

This Part fo EN 12201 specifies the characteristics of the fitness for purpose of the assembled piping systems intended for the conveyance of water inended for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.

DIN EN 12201-5:2011 Referenced Document

• EN 12201-1 Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 1: General*， 2024-01-31 Update
• EN 12201-2 Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 2: Pipes*， 2024-01-31 Update
• EN 12201-3 Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 3: Fittings*， 2024-01-31 Update
• EN 712 Thermoplastics Piping Systems - End-Load Bearing Mechanical Joints Between Pressure Pipes and Fittings - Test Method for Resistance to Pull-Out Under Constant Longitudinal Force
• EN 713 Plastics Piping Systems - Mechanical Joints Between Fittings and Polyolefin Pressure Pipes - Test Method for Leaktightness Under Internal Pressure of Assemblies Subjected to Bending
• EN 715 Thermoplastics Piping Systems - End-Load- Bearing Joints Between Small Diameter Pressure Pipes and Fittings - Test Method for Leaktightness Under Internal Water Pressure, Including End Thrust
• EN 911 Plastics Piping Systems - Elastomeric Sealing Ring Type Joints and Mechanical Joints for Thermoplastics Pressure Piping - Test Method for Leaktightness under External Hydrostatic Pressure
• EN ISO 1167-1 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
• EN ISO 1167-2 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
• EN ISO 1167-4 Thermoplastics pipes@ fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies
• ISO 11413:2008 Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
• ISO 11414:2009 Plastics pipes and fittings - Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
• ISO 13953 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint — Amendment 1*， 2020-04-20 Update
• ISO 13954 Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm — Amendment 1*， 2020-04-20 Update
• ISO 13955 Plastics pipes and fittings — Crushing decohesion test for polyethylene (PE) electrofusion assemblies — Amendment 1*， 2020-04-20 Update
• ISO 14236 Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems

DIN EN 12201-5:2011 history

• 2021 DIN EN 12201-5:2021-05 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the System; German and English version prEN 12201-5:2021 / Note: Date of issue 2021-04-02*Intended as replacemen...
• 2013 DIN EN 14511-4:2013 Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling - Part 4: Operating requirements, marking and instructions; German version EN 14511-4:2013
• 2011 DIN EN 12201-5:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system; German version EN 12201-5:2011
• 2003 DIN EN 12201-5:2003 Plastic piping systems for water supply
• 1970 DIN EN 12201-5 E:1996-02 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system