ISO 14236:2000
Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems

Standard No.

ISO 14236:2000

Release Date

2000

Published By

International Organization for Standardization (ISO)

Latest

ISO 14236:2000

Scope

This International Standard specifies the required properties and test methods for mechanical fittings intended to join polyethylene pressure pipes of nominal outside diameters not greater than 160 mm, used in water supply systems conveying potable water and water for general purposes at temperatures up to and including 40 ℃. The nominal pressure of the specified mechanical fittings corresponds at least to the PN of the water supply system for which they are designed and is usually of PN 6, PN 10 or PN 16.

ISO 14236:2000 Referenced Document

• EN 1254-3:1998 Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes
• ISO 1083:1987 Spheroidal graphite cast iron; Classification
• ISO 1167:1996 Thermoplastics pipes for the conveyance of fluids - Resistance to internal pressure - Test method
• ISO 12092 Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure - R*， 2000-04-01 Update
• ISO 12162:1995 Thermoplastics materials for pipes and fittings for pressure applications - Classification and designation - Overall service (design) coefficient
• ISO 15853:1999 Thermoplastic materials - Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for injection moulding
• ISO 161-1:1996 Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Part 1: Metric series
• ISO 197-1:1983 Copper and copper alloys; Terms and definitions; Part 1 : Materials
• ISO 197-4:1983 Copper and copper alloys; Terms and definitions; Part 4 : Castings
• ISO 228-1:1994 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
• ISO 3459:1976 Polyethylene (PE) pressure pipes; Joints assembled with mechanical fittings; Internal under-pressure test method and requirement
• ISO 3501:1976 Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of resistance to pull out
• ISO 3503:1976 Assembled joints between fittings and polyethylene (PE) pressure pipes; Test of leakproofness under internal pressure when subjected to bending
• ISO 426-1:1983 Wrought copper-zinc alloys; Chemical composition and forms of wrought products; Part 1 : Non-leaded and special copper-zinc alloys
• ISO 426-2:1983 Wrought copper-zinc alloys; Chemical composition and forms of wrought products; Part 2 : Leaded copper-zinc alloys
• ISO 427:1983 Wrought copper-tin alloys; Chemical composition and forms of wrought products
• ISO 4427:1996 Polyethylene (PE) pipes for water supply - Specifications
• ISO 5922:1981 Malleable cast iron
• ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads - Part 1: Dimensions, tolerances and designation
• ISO 7686:1992 Plastics pipes and fittings; opacity; test method
• ISO 9080 Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation*， 2012-10-01 Update
• ISO 9853:1991 Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings for pressure pipe systems; crushing test

ISO 14236:2000 history

• 2000 ISO 14236:2000 Plastics pipes and fittings - Mechanical-joint compression fittings for use with polyethylene pressure pipes in water supply systems