ASTM D7745-11
Standard Practice for Testing Pultruded Composites
- Standard No.
- ASTM D7745-11
- Release Date
- 2011
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D7745-19
- Latest
- ASTM D7745-19
- Scope
This practice is intended to aid in the selection of test protocols for reinforced pultruded composites.
This practice is intended to define the locations from which test specimens shall be taken from the reinforced pultruded composite.
1.1 This protocol summarizes the applicable ASTM and other standard test methods commonly used for pultruded composites. The individual performance requirements to these test methods are defined by specific customer specifications.
1.2 This protocol also defines appropriate specimen locations for sampling from the pultruded composites.
1.3 This protocol does not discuss all possible standard test methods that may be utilized for pultruded composites.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 18212;There is no known ISO equivalent to this guide.
ASTM D7745-11 Referenced Document
- ASTM D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
- ASTM D2344/D2344M Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates
- ASTM D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
- ASTM D2583 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
- ASTM D2584 Standard Test Method for Ignition Loss of Cured Reinforced Resins
- ASTM D3039/D3039M Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
- ASTM D3916 Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod
- ASTM D3918 Standard Terminology Relating to Reinforced Plastic Pultruded Products
- ASTM D4065 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
- ASTM D495 Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
- ASTM D5379/D5379M Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
- ASTM D5420 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
- ASTM D570 Standard Test Method for Water Absorption of Plastics
- ASTM D635 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
- ASTM D638 Standard Test Method for Tensile Properties of Plastics
- ASTM D6641/D6641M Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture
- ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics
- ASTM D696 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30176C and 30176C With a Vitreous Silica Dilatometer
- ASTM D7136/D7136M Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event
- ASTM D7332/D7332M Standard Test Method for Measuring the Fastener Pull-Through Resistance of a
Fiber-Reinforced Polymer Matrix Composite - ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials*， 2024-04-19 Update
- ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
- ASTM D953 Standard Test Method for Bearing Strength of Plastics
- ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
- ASTM G154 Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials
ASTM D7745-11 history
- 2019 ASTM D7745-19 Standard Practice for Testing Pultruded Composites
- 2011 ASTM D7745-11 Standard Practice for Testing Pultruded Composites
