ASTM D7745-19
Standard Practice for Testing Pultruded Composites

Standard No.

ASTM D7745-19

Release Date

2019

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D7745-19

Scope

1.1 This protocol summarizes the applicable ASTM and other standard test methods commonly used for pultruded composites. The individual performance requirements to these test methods are defined by specific customer specifications. 1.2 This protocol also defines appropriate specimen locations for sampling from the pultruded composites. 1.3 This protocol does not discuss all possible standard test methods that may be utilized for pultruded composites. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this guide. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D7745-19 Referenced Document

• ASTM D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
• ASTM D2291 Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites
• ASTM D2343 Standard Test Method for Tensile Properties of Glass Fiber Strands, Yarns, and Rovings Used in Reinforced Plastics
• ASTM D2344/D2344M Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates*， 2022-07-15 Update
• ASTM D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics*， 2023-03-15 Update
• ASTM D2583 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
• ASTM D2584 Standard Test Method for Ignition Loss of Cured Reinforced Resins
• ASTM D2734 Standard Test Methods for Void Content of Reinforced Plastics
• ASTM D3039/D3039M Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
• ASTM D3647 Standard Practice for Classifying Reinforced Plastic Pultruded Shapes According to Composition
• ASTM D3846 Standard Test Method for In-Plane Shear Strength of Reinforced Plastics
• ASTM D3914 Standard Test Method for In-Plane Shear Strength of Pultruded Glass-Reinforced Plastic Rod
• ASTM D3916 Standard Test Method for Tensile Properties of Pultruded Glass-Fiber-Reinforced Plastic Rod
• ASTM D3917 Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes
• ASTM D4065 Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures
• ASTM D4385 Standard Practice for Classifying Visual Defects in Thermosetting Reinforced Plastic Pultruded Products
• ASTM D4475 Standard Test Method for Apparent Horizontal Shear Strength of Pultruded Reinforced Plastic Rods By The Short-Beam Method
• ASTM D4476 Standard Test Method for Flexural Properties of Fiber Reinforced Pultruded Plastic Rods
• ASTM D495 Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
• ASTM D5028 Standard Test Method for Curing Properties of Pultrusion Resins by Thermal Analysis
• ASTM D5117 Standard Test Method for Dye Penetration of Solid Fiberglass Reinforced Pultruded Stock
• ASTM D5379/D5379M Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
• ASTM D5420 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
• ASTM D570 Standard Test Method for Water Absorption of Plastics
• ASTM D635 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
• ASTM D638 Standard Test Method for Tensile Properties of Plastics
• ASTM D6641/D6641M Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture*， 2023-11-15 Update
• ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics
• ASTM D696 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30176C and 30176C With a Vitreous Silica Dilatometer
• ASTM D7029 Standard Test Method for Determination of Reactivity of Unsaturated Polyesters and Vinyl Esters at 180.0°F (82.2°C)
• ASTM D7136/D7136M Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer Matrix Composite to a Drop-Weight Impact Event*， 2020-10-01 Update
• ASTM D7290 Standard Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications*， 2022-02-01 Update
• ASTM D732 Standard Test Method for Shear Strength of Plastics by Punch Tool
• ASTM D7332/D7332M Standard Test Method for Measuring the Fastener Pull-Through Resistance of a Fiber-Reinforced Polymer Matrix Composite*， 2023-09-01 Update
• ASTM D7792/D7792M Standard Practice for Freeze/Thaw Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs*， 2023-12-15 Update
• ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials*， 2024-04-22 Update
• ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
• ASTM D7992/D7992M Standard Practice for Elevated Temperature and Moisture Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs*， 2023-12-15 Update
• ASTM D8019 Standard Test Methods for Determining the Full Section Flexural Modulus and Bending Strength of Fiber Reinforced Polymer Crossarms Assembled with Center Mount Brackets*， 2023-11-01 Update
• ASTM D8069 Standard Test Method for Determining Flexural Modulus of Full Section Pultruded Fiber Reinforced Polymer (FRP) Composite Members with Doubly Symmetric Cross Sections under Bending
• ASTM D883 Standard Terminology Relating to Plastics*， 2024-02-01 Update
• ASTM D953 Standard Test Method for Bearing Strength of Plastics
• ASTM E1922 Standard Test Method for Translaminar Fracture Toughness of Laminated Polymer Matrix Composite Materials
• ASTM E662 Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials
• ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
• ASTM F1092 Standard Specification for Fiberglass (GRP) Pultruded Open-Weather Storm- and Guard-Square Handrails
• ASTM G154 Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials*， 2023-01-01 Update

ASTM D7745-19 history

• 2019 ASTM D7745-19 Standard Practice for Testing Pultruded Composites
• 2011 ASTM D7745-11 Standard Practice for Testing Pultruded Composites