This standard applies to the empty housing provided by the housing manufacturer (hereinafter referred to as the housing), which is the product of the user before the installation of switchgear and control gear components. This standard specifies the definition, classification, performance and test requirements for housings used in low-voltage complete switchgear and control equipment that comply with GB 7251 series standards. The rated voltage of the low-voltage switchgear and control equipment is not more than 1000V for AC, 1000Hz for frequency or 1500V for DC, suitable for indoor or outdoor use. This standard does not apply to housings mentioned in other specific product standards (such as IEC 60670). The final turnkey equipment manufacturer is responsible for the safety requirements of the corresponding product standards.
GB/T 20641-2006 Referenced Document
GB 4208-1993 Degrees of protection provided by enclosure (IP code)
GB 7251.1-2005 Low-voltage switchgear and controlgear assemblies-Part 1:Type-tested and partially type-tested assemblies
GB 7251.12 Low-voltage switchgear and controlgear assemblies.Part 2:Power switchgear and controlgear assemblies*, 2013-12-31 Update
GB 7251.2 Low-voltage switchgear and controlgear assemblies. Part 2: Particular requirements for busbar trunking systems (busways)
GB 7251.3 Low-voltage switchgear and controlgear assemblies. Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use. Distribution boards
GB 7251.4 Low-voltage switchgear and controlgear assemblies Part 4: Particular requirements for assemblies for construction sites (ACS)*, 2006-12-01 Update
GB 7251.5 Low-voltage switchgear and control equipment Part 5: Public grid power distribution equipment*, 2017-07-31 Update
GB 7251.5-1998 Low-voltage switchgear and controlgear assemblies Part 5: Particular requirements for assemblies intended to be installed outdoors in public places--Cable distribution cabinets (CDCs)for power distribution in networks
GB 7251.6 Low-voltage switchgear and controlgear assemblies.Part 6:Busbar trunking systems (busways)*, 2015-05-15 Update
GB/T 16422.2-1999 Plastics--Methods of exposure to laboratory light sources Part 2: Xenon--arc sources
GB/T 2423.2-2001 Environmental testing for electric and electronic products Part 2: Test methods Tests B: Dry heat
IEC 60068-2-11:1981 Basic environmental testing procedures. Part 2 : Tests. Test Ka: Salt mist
IEC 60068-2-30:1980 Basic environmental testing procedures. Part 2 : Tests. Test Db and guidance: Damp heat, cyclic (12 + 12-hour cycle)
IEC 60068-2-75:1997 Environmental testing - Part 2: Tests - Test Eh: Hammer tests
IEC 60695-2-10:2000 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods; Glow-wire apparatus and common test procedure
IEC 60695-2-11:2000 Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods; Glow-wire flammability test method for end-products
IEC 61000-5-7 Electromagnetic compatibility (EMC) - Part 5-7: Installation and mitigation guidelines; Degrees of protection provided by enclosures against electromagnetic disturbances (EM code)
IEC 62262:2002 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
ISO ISO IEC 27001-2013 cor2-2015 technical errata*, 2024-04-18 Update
ISO 178:2001 Plastics - Determination of flexural properties
ISO 179 Plastics — Determination of Charpy impact strength — Technical Corrigendum 1
GB/T 20641-2006 history
2014GB/T 20641-2014 Empty enclosures for low-voltage switchgear and controlgear assemblies.General requirements
2006GB/T 20641-2006 Empty enclosures for low-voltage switchgear and controlgear assemblies General requirements