DIN EN 681-2:2006
Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-2:2006-11

Standard No.

DIN EN 681-2:2006

Release Date

2006

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN 681-2:2006-11

Latest

DIN EN 681-2:2006-11

Replace

DIN EN 681-2:2003

Scope

This standard specifies requirements for materials used for moulded seals only of thermoplastic elastomers (TPE) used in joints of: 1) thermoplastic piping systems for non pressure waste water discharge (intermittent flow up to 95℃) inside buildings; 2) thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow up to 45℃ and intermittent flow up to 95℃); 3) thermoplastic rainwater piping systems. General requirements for finished joint seals are slso given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.

DIN EN 681-2:2006 Referenced Document

• ISO 1431-1 Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing*， 2022-06-23 Update
• ISO 1817 Rubber, vulcanized or thermoplastic*， 2024-02-01 Update
• ISO 188 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests*， 2023-03-09 Update
• ISO 2859-1 Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection; Technical Corrigendum 1
• ISO 3302-1 Rubber - Tolerances for products - Part 1: Dimensional tolerances*， 2014-07-01 Update
• ISO 3384:1999 Rubber, vulcanized or thermoplastic - Determination of stress relaxation in compression at ambient and at elevated temperatures
• ISO 37 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties*， 2017-11-01 Update
• ISO 3951 Sampling procedures and charts for inspection by variables for percent nonconforming
• ISO 4661-1 Rubber, vulcanized or thermoplastic; preparation of samples and test pieces; part 1: physical tests
• ISO 471 Rubber - Temperatures, humidities and times for conditioning and testing
• ISO 48 Rubber, vulcanized or thermoplastic - Determination of hardness (hardness between 10 IRHD and 100 IRHD)*， 2010-09-01 Update
• ISO 815 Rubber, vulcanized or thermoplastic; determination of compression set at ambient, elevated or low temperatures; Technical Corrigendum 1
• ISO 9691:1992 Rubber; recommendations for the workmanship of pipe joint rings; description and classification of imperfections

DIN EN 681-2:2006 history

• 2006 DIN EN 681-2:2006-11 Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers; German version EN 681-2:2000 + A1:2002 + A2:2005
• 2006 DIN EN 681-2:2006 Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers (includes Amendments A1:2002 + A2:2005); English version of DIN EN 681-2:2006-11
• 2000 DIN EN 681-2:2003 Elastomeric seals — Material requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers