ISO 12086-2:2006 Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
1.1 This part of ISO 12086 describes the preparation of test specimens and provides test methods to define
characteristics of thermoplastic fluoropolymer resins. Results from the testing may be used as the basis for
designation, material specifications or both. This part of ISO 12086 describes the conditions of test for
determining both designatory and other properties of the homopolymers and various copolymers of
fluoromonomers, as dispersions or powders for moulding, extrusion and other uses. The test procedures
included are appropriate for, but are not restricted to, the fluoropolymers listed in Clause 4 and for which
designatory properties are specified in ISO 12086-1.
1.2 The properties of semi-finished and finished products made from fluoropolymer resins depend on the
material used, the shape of the product, the physical and morphological state of the material resulting from the
processing operations, and on the test conditions. Therefore, to obtain reproducible test results, the defined
methods of preparation of test specimens and defined test conditions given in this part of ISO 12086 must be
applied.
1.3 Agreements between vendor and purchaser should preferably be based on properties measured using
the specimens and test conditions described in this part of ISO 12086.
ISO 12086-2:2006 Referenced Document
BS 4641:1986 Method for specifying electroplated coatings of chromium for engineering purposes
IEC 60093 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
IEC 60243-1 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies*, 2013-03-01 Update
IEC 60250 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
ISO 1043-1 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics AMENDMENT 1: New symbol ST for syndiotactic*, 2011-01-01 Update
ISO 1043-2 Plastics - Symbols and abbreviated terms - Part 2: Fillers and reinforcing materials*, 2011-11-01 Update
ISO 1133:2005 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
ISO 11357-2 Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and step height*, 2020-03-02 Update
ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization*, 2018-03-01 Update
ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method*, 2019-02-28 Update
ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*, 2019-02-28 Update
ISO 12086-1 Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications; Technical Corrigendum 1*, 2006-08-01 Update
ISO 13320-1 Particle size analysis - Laser diffraction methods - Part 1: General principles
ISO 178 Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers*, 2019-04-01 Update
ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*, 2023-06-07 Update
ISO 180 Plastics. Determination of Izod impact strength*, 2023-06-07 Update
ISO 291 Plastics - Standard atmospheres for conditioning and testing*, 2008-05-01 Update
ISO 293 Plastics — Compression moulding of test specimens of thermoplastic materials*, 2023-02-21 Update
ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles*, 2019-07-26 Update
ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics*, 2012-02-01 Update
ISO 527-3 Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets*, 2018-11-05 Update
ISO 565 Test sieves; metal wire cloth, perforated metal plate and electroformed sheet; nominal sizes of openings
ISO 75-2 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite*, 2013-04-01 Update
ISO 976 Rubber and plastics.Polymer dispersions and rubber latices.Determination of pH*, 2013-12-03 Update
ISO 12086-2:2006 history
2006ISO 12086-2:2006/cor 1:2006 Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties; Technical Corrigendum 1
2006ISO 12086-2:2006 Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
1995ISO 12086-2:1995 Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties