ISO 14526-2:1999
Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties

Standard No.

ISO 14526-2:1999

Release Date

1999

Published By

International Organization for Standardization (ISO)

Latest

ISO 14526-2:1999

Scope

This part of GB/T 1404 specifies the test methods for sample preparation and performance determination of powdered phenolic molding compounds (PF-PMCs). It also provides the processing requirements of test materials and the condition adjustment requirements of test materials before molding and specimens before testing. This section gives the procedures and conditions for specimen preparation and performance testing using these specimens. It also lists the applicable and necessary properties and test methods for characterizing PMCs. These properties are selected from the general test methods in GB/T 19467.1-2004. Other test methods that are widely used or particularly important for PMCs are included in this section, and their characteristic properties comply with the provisions of 4.4.3 and 4.4.4 in GB/T 1404.1-2008. In order to obtain reproducible and comparable test results, the specimen preparation and conditioning methods, specimen dimensions and test procedures specified in the standard must be adopted. Data obtained using different sample sizes or different preparation steps may not be consistent.

ISO 14526-2:1999 Referenced Document

• IEC 60093:1980 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
• IEC 60112:1979 Recommended method for determining the comparative tracking index of solid insulating materials under moist conditions
• IEC 60167:1964 Methods of test for the determination of the insulation resistance of solid insulating materials
• IEC 60243-1:1998 Electrical strength of insulating materials - Test methods - Part 1: Tests at power frequencies
• IEC 60250:1969 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
• IEC 60296:1982 Specification for unused mineral insulating oils for transformers and switchgear
• IEC 60695-11-10:1999 Fire hazard testing - Part 11-10: Test flames; 50 W horizontal and vertical flame test methods
• IEC 60695-11-20:1999 Fire hazard testing - Part 11-20: Test flames; 500 W flame test methods
• IEC 60707:1999 Flammability of solid non-metallic materials when exposed to flame sources - List of test methods
• ISO 10350-1:1998 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
• ISO 10724-1:1998 Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens
• ISO 10724-2:1998 Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates
• ISO 11359-2:1999 Plastics - Thermomechanical analysis (TMA) - Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
• ISO 1183:1987 Plastics; Methods for determining the density and relative density of non-cellular plastics
• ISO 120:1977 Plastics; Phenol-formaldehyde mouldings; Determination of free ammonia and ammonium compounds; Colorimetric comparison method
• ISO 14526-1:1999 Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 1: Designation system and basis for specifications
• ISO 14526-3:1999 Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 3: Requirements for selected moulding compounds
• ISO 171:1980 Plastics; Determination of bulk factor of moulding materials
• ISO 178:1993 Plastics; determination of flexural properties
• ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*， 2023-06-07 Update
• ISO 2039-1:1993 Plastics; determination of hardness; part 1: ball indentation method
• ISO 2577:1984 Plastics; Thermosetting moulding materials; Determination of shrinkage
• ISO 2818:1994 Plastics - Preparation of test specimens by machining
• ISO 291:1997 Plastics - Standard atmospheres for conditioning and testing
• ISO 295 Plastics - Compression moulding of test specimens of thermosetting materials*， 2004-02-01 Update
• ISO 3167:1993 Plastics; multipurpose test specimens
• ISO 3671:1976 Plastics; Aminoplastic moulding materials; Determination of volatile matter
• ISO 4589-2:1996 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test
• ISO 4614:1977 Plastics; Melamine-formaldehyde mouldings; Determination of extractable formaldehyde
• ISO 472:1999 Plastics - Vocabulary
• ISO 527-1:1993 Plastics; determination of tensile properties; part 1: general principles
• ISO 527-2:1993 Plastics; determination of tensile properties; part 2: test conditions for moulding and extrusion plastics
• ISO 60:1977 Plastics; Determination of apparent density of material that can be poured from a specified funnel
• ISO 62:1999 Plastics - Determination of water absorption
• ISO 6603-2 Plastics. Determination of puncture impact behaviour of rigid plastics. - Part 2: Instrumented impact testing*， 2023-06-02 Update
• ISO 75-2:1993 Plastics; determination of temperature of deflection under load; part 2: plastics and ebonite
• ISO 7808:1992 Plastics; thermosetting moulding materials; determination of transfer flow
• ISO 800:1992 Plastics; phenolic moulding materials; specification
• ISO 8256:1990 Plastics; determination of tensile-impact strength
• ISO 899-1:1993 Plastics; determination of creep behaviour; part 1: tensile creep

ISO 14526-2:1999 history

• 1999 ISO 14526-2:1999 Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties