ASTM C183/C183M-22
Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- Standard No.
- ASTM C183/C183M-22
- Release Date
- 2022
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C183/C183M-23
- Latest
- ASTM C183/C183M-23
- Scope
- 1.1 This practice covers procedures for sampling and for the amount of testing of hydraulic cement after it has been manufactured and is ready to be offered for sale. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in Standard IEEE/ASTM SI 10, Values are stated in only SI units when inch-pound units are not used in practice 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered requirements of the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C183/C183M-22 Referenced Document
- ASTM C10/C10M Standard Specification for Natural Cement
- ASTM C1012/C1012M Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution*， 2024-04-01 Update
- ASTM C1038/C1038M Standard Test Method for Expansion of Hydraulic Cementitious Material Mortar Bars Stored in Water*， 2024-04-01 Update
- ASTM C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
- ASTM C114 Standard Test Methods for Chemical Analysis of Hydraulic Cement*， 2023-10-01 Update
- ASTM C1157/C1157M Standard Performance Specification for Hydraulic Cement*， 2023-09-01 Update
- ASTM C1328/C1328M Standard Specification for Plastic (Stucco) Cement*， 2023-01-01 Update
- ASTM C1329/C1329M Standard Specification for Mortar Cement*， 2023-01-01 Update
- ASTM C1357 Standard Test Methods for Evaluating Masonry Bond Strength
- ASTM C150/C150M Standard Specification for Portland Cement
- ASTM C1506 Standard Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters
- ASTM C151/C151M Standard Test Method for Autoclave Expansion of Hydraulic Cement*， 2023-12-01 Update
- ASTM C157/C157M Standard Test Method for Length Change of Hardened Hydraulic-Cement, Mortar, and Concrete
- ASTM C1702 Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry*， 2023-08-01 Update
- ASTM C185 Standard Test Method for Air Content of Hydraulic Cement Mortar
- ASTM C191 Standard Test Method for Time of Setting of Hydraulic Cement by Vicat Needle
- ASTM C204 Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus
- ASTM C266 Standard Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles
- ASTM C430 Standard Test Method for Fineness of Hydraulic Cement by the 45-956;m (No. 325) Sieve
- ASTM C451 Standard Test Method for Early Stiffening of Hydraulic Cement (Paste Method)
- ASTM C452/C452M Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate*， 2024-04-22 Update
- ASTM C595/C595M Standard Specification for Blended Hydraulic Cements*， 2023-07-15 Update
- ASTM C806 Standard Test Method for Restrained Expansion of Expansive Cement Mortar
- ASTM C807 Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle
- ASTM C845/C845M Standard Specification for Expansive Hydraulic Cement
- ASTM C91/C91M Standard Specification for Masonry Cement*， 2023-01-01 Update
- ASTM E11 Standard Specification for Wire Cloth and Sieves for Testing Purposes
- IEEE/ASTM SI 10 American National Standard for Metric Practice
ASTM C183/C183M-22 history
- 2023 ASTM C183/C183M-23 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- 2022 ASTM C183/C183M-22 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- 2016 ASTM C183/C183M-16 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- 2015 ASTM C183/C183M-15 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- 2013 ASTM C183-13 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- 2008 ASTM C183-08 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- 2002 ASTM C183-02 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
- 1997 ASTM C183-97 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
