1.1 This specification covers the minimum performance and material requirements for resilient connectors used for connections between reinforced concrete manholes conforming to Specification C478/C478M and pipes, between wastewater structures and pipes, and between precast reinforced concrete pipe and laterals.
1.1.1 These connectors are designed to minimize leakage between the pipe and manhole, and between the pipe and lateral.
1.2 The values stated in inch pound or SI units are to be regarded separately as standard. The SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. NOTE 1—This specification covers the design, material, and performance of the resilient connection only. Connections covered by this specification are adequate for hydrostatic pressures up to 13 psi (30 ft) [90 kPa (9.1 m)] without leakage when tested in accordance with Section 7. Infiltration or exfiltration quantities for an installed system are dependent upon many factors other than the connections between manhole structures and pipe, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precaution statement, see
7.2.5.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C923/C923M-20 Referenced Document
ASTM A493 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging
ASTM A666 Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar*, 2023-03-01 Update
ASTM C478/C478M Standard Specification for Circular Precast Reinforced Concrete Manhole Sections*, 2022-09-01 Update
ASTM C822 Standard Terminology Relating to Concrete Pipe and Related Products
ASTM C913 Standard Specification for Precast Concrete Water and Wastewater Structures
ASTM D1149 Standard Test Method for Rubber Deterioration-Surface Ozone Cracking in a Chamber
ASTM D1566 Standard Terminology Relating to Rubber*, 2021-11-01 Update
ASTM D2137 Standard Test Methods for Rubber Property-Brittleness Point of Flexible Polymers and Coated Fabrics
ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*, 2024-04-22 Update
ASTM D395 Standard Test Methods for Rubber Property-Compression Set
ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers8212;Tension
ASTM D471 Standard Test Method for Rubber Property-Effect of Liquids
ASTM D543 Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D573 Standard Test Method for Rubber-Deterioration in an Air Oven
ASTM D624 Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers*, 2024-04-22 Update
ASTM D883 Standard Terminology Relating to Plastics*, 2024-02-01 Update
ASTM C923/C923M-20 history
2020ASTM C923/C923M-20 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
2018ASTM C923-18 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
2008ASTM C923-08(2013)e1 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
2008ASTM C923-08(2013) Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
2008ASTM C923-08 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
2007ASTM C923-07 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
2002ASTM C923-02 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes and Laterals
2000ASTM C923-00 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes and Laterals