ASTM A1010/A1010M-24
Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip

Standard No.

ASTM A1010/A1010M-24

Release Date

2024

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM A1010/A1010M-24

Scope

1.1 This specification covers martensitic stainless steels for various structural, architectural, pressure vessel, and heatresisting applications. The mechanical properties of these steels are customarily, but not necessarily, developed by a suitable heat treatment generally referred to as tempering.

1.2 Steel products under this specification are available in two grades: Grade Yield Strength, min, ksi [MPa] 40 [275] 40 [275] 50 [345] 50 [345] 1.3 The maximum thickness of plates is limited only by the capacity of the composition to meet the specified mechanical property requirements; however, current practice normally limits the maximum thickness of plates furnished under this specification to 2 in. [50 mm].

1.4 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.5 Supplementary requirements are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM A1010/A1010M-24 Referenced Document

• ASTM A480/A480M Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
• ASTM A673/A673M Standard Specification for Sampling Procedure for Impact Testing of Structural Steel
• ASTM A941 Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys*， 2025-03-01 Update
• ASTM E527 Standard Practice for Numbering Metals and Alloys (UNS)
• SAE J1086 Numbering Metals and Alloys

ASTM A1010/A1010M-24 history

• 2024 ASTM A1010/A1010M-24 Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
• 2018 ASTM A1010/A1010M-13(2018) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
• 2013 ASTM A1010/A1010M-13 Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet, and Strip
• 2001 ASTM A1010/A1010M-01(2009) Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet , and Strip
• 2001 ASTM A1010/A1010M-01e1 Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet , and Strip
• 2001 ASTM A1010-01 Standard Specification for Higher-Strength Martensitic Stainless Steel Plate, Sheet , and Strip

Standard and Specification