ASTM F3318-18
Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam

Standard No.

ASTM F3318-18

Release Date

2018

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM F3318-18

Scope

1.1 This specification covers additively manufactured AlSi10Mg (similar to DIN EN 1706:2013-12 EN AC-43000) parts using powder bed fusion such as laser melting. The parts produced by these processes are used typically in applications that require mechanical properties similar to or exceeding those of cast aluminum products of equivalent alloys. Parts manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions. 1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured AlSi10Mg parts for defining the requirements and ensuring part properties. 1.3 Users are advised to use this specification as a basis for obtaining parts that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee. 1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more supplementary requirements, which may include, but are not limited to, those listed in Supplementary Requirements S1–S16. 1.5 The values stated in SI units are to be regarded as the standard. Other units are included only for informational purposes. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F3318-18 Referenced Document

• ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay) ( - 2009)
• ASTM B213 Standard Test Method for Flow Rate of Metal Powders
• ASTM B214 Standard Test Method for Sieve Analysis of Metal Powders
• ASTM B243 Standard Terminology of Powder Metallurgy*， 2023-05-01 Update
• ASTM B311 Test Method for Density Determination for Powder Metallurgy (P/M) Materials Containing Less Than Two Percent Porosity
• ASTM B769 Standard Test Method for Shear Testing of Aluminum Alloys
• ASTM B855 Standard Test Method for Volumetric Flow Rate of Metal Powders Using Arnold Meter and Hall Funnel
• ASTM B964 Standard Test Methods for Flow Rate of Metal Powders Using the Carney Funnel*， 2023-02-01 Update
• ASTM D3951 Standard Practice for Commercial Packaging
• ASTM E10 Standard Test Method for Brinell Hardness of Metallic Materials*， 2023-08-03 Update
• ASTM E11 Standard Specification for Wire Cloth and Sieves for Testing Purposes
• ASTM E1251 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Argon Atmosphere, Point-to-Plane, Unipolar Self-Initiating Capacitor Discharge
• ASTM E1417 Standard Practice for Liquid Penetrant Examination
• ASTM E1450 Standard Test Method for Tension Testing of Structural Alloys in Liquid Helium
• ASTM E1479 Standard Practice for Describing and Specifying Inductively-Coupled Plasma Atomic Emission Spectrometers
• ASTM E155 Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings*， 2020-06-01 Update
• ASTM E1742 Standard Practice for Radiographic Examination*， 2024-04-21 Update
• ASTM E18 Standard Test Methods for Rockwell Hardness of Metallic Materials*， 2022-05-01 Update
• ASTM E1820 Standard Test Method for Measurement of Fracture Toughness
• ASTM E21 Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
• ASTM E23 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
• ASTM E2368 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing*， 2024-04-21 Update
• ASTM E238 Standard Test Method for Pin-Type Bearing Test of Metallic Materials
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• ASTM E3 Standard Practice for Preparation of Metallographic Specimens
• ASTM E34 Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
• ASTM E384 Standard Test Method for Microindentation Hardness of Materials
• ASTM E399 Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials
• ASTM E407 Standard Practice for Microetching Metals and Alloys
• ASTM E466 Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials
• ASTM E606 Standard Practice for Strain-Controlled Fatigue Testing
• ASTM E607 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique, Nitrogen Atmosphere
• ASTM E647 Standard Test Method for Measurement of Fatigue Crack Growth Rates
• ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials*， 2024-01-01 Update
• ASTM E9 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
• ASTM F2971 Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing*， 2021-07-15 Update
• ASTM F3049 Standard Guide for Characterizing Properties of Metal Powders Used for Additive Manufacturing Processes*， 2021-10-01 Update
• ISO 1099 Metallic materials - Fatigue testing - Axial force-controlled method
• ISO 12108 Metallic materials - Fatigue testing - Fatigue crack growth method*， 2018-07-01 Update
• ISO 12111 Metallic materials - Fatigue testing - Strain-controlled thermomechanical fatigue testing method
• ISO 12135 Metallic materials - Unified method of test for the determination of quasistatic fracture toughness*， 2021-06-30 Update
• ISO 12737 Metallic materials — Determination of plane-strain fracture toughness
• ISO 148-1 Metallic materials - Charpy pendulum impact test - Part 1: Test method
• ISO 19819 Metallic materials - Tensile testing in liquid helium
• ISO 4545 Metallic materials; hardness test; Knoop test
• ISO 6506-1 Metallic materials - Brinell hardness test - Part 1: Test method
• ISO 6507-1 Metallic materials — Vickers hardness test — Part 1: Test method*， 2023-08-01 Update
• ISO 6508 Metallic materials; Hardness test; Rockwell test (scales A - B - C - D - E - F - G - H - K)
• ISO 6892-1 Metallic materials — Tensile testing — Part 1: Method of test at room temperature*， 2019-11-15 Update
• ISO 6892-2 Metallic materials - Tensile testing- Part 2:Method of test at elevated temperature
• ISO 9001 Quality management systems - Requirements [Spanish version]
• ISO 9044 Industrial woven wire cloth - Technical requirements and tests
• SAE AMS2175 Castings, Classification and Inspection of
• SAE AMS2771 HEAT TREATMENT OF ALUMINUM ALLOY CASTINGS

ASTM F3318-18 history

• 2018 ASTM F3318-18 Standard for Additive Manufacturing – Finished Part Properties – Specification for AlSi10Mg with Powder Bed Fusion – Laser Beam