ASTM F468M-06(2018)
Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
- Standard No.
- ASTM F468M-06(2018)
- Release Date
- 2018
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM F468-10
- Latest
- ASTM F468-23
- Scope
- 1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs in nominal thread diameters M6 to M36 inclusive manufactured from a number of alloys in common use and intended for general service applications. 1.2 Unless otherwise specified, nuts used on these bolts, cap screws, and studs shall conform to the requirements of Specification F467M. Nuts shall be of the same alloy group as the fastener on which they are used and shall have a specified minimum proof stress equal to or greater than the specified minimum tensile strength stress of the fastener on which they are used. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. NOTE 1—This specification is the metric companion of Specification F468. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F468M-06(2018) Referenced Document
- ASTM B154 Standard Test Method for Mercurous Nitrate Test for Copper and Copper Alloys
- ASTM B193 Standard Test Method for Resistivity of Electrical Conductor Materials
- ASTM B211M Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire [Metric]
- ASTM B565 Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods
- ASTM B574 Spec for Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod
- ASTM D3951 Standard Practice for Commercial Packaging
- ASTM E101
- ASTM E120 Standard Test Methods for Chemical Analysis of Titanium and Titanium Alloys (Withdrawn 2003)
- ASTM E1409 Standard Test Method for Determination of Oxygen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique
- ASTM E165 Standard Test Method for Liquid Penetrant Examination
- ASTM E18 Standard Test Methods for Rockwell Hardness of Metallic Materials*， 2022-05-01 Update
- ASTM E227 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002)*， 2021-02-18 Update
- ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
- ASTM E34 Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
- ASTM E354 Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys
- ASTM E38
- ASTM E478 Standard Test Methods for Chemical Analysis of Copper Alloys
- ASTM E53 Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
- ASTM E54
- ASTM E55 Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
- ASTM E62 Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
- ASTM E75 Standard Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
- ASTM E76 Standard Test Methods for Chemical Analysis of Nickel-Copper Alloys (Withdrawn 2003)
- ASTM E8M Standard Test Methods for Tension Testing of Metallic Materials [Metric] *， 2024-04-21 Update
- ASTM E92 Standard Test Method for Vickers Hardness of Metallic Materials
- ASTM F1470 Standard Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection*， 2024-01-26 Update
- ASTM F467M Standard Specification for Nonferrous Nuts for General Use [Metric]
- ASTM F606/F606M Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets*， 2021-06-01 Update
ASTM F468M-06(2018) history
- 2023 ASTM F468-23 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
- 2022 ASTM F468-22 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
- 2016 ASTM F468-16 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
- 2015 ASTM F468-15e1 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
- 2015 ASTM F468-15 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
- 2013 ASTM F468-13 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
- 2012 ASTM F468-12 Standard Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use
- 2010 ASTM F468-10 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
- 2018 ASTM F468M-06(2018) Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
- 2006 ASTM F468M-06(2012) Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use (Metric)
- 2006 ASTM F468M-06e1 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 2006 ASTM F468M-06 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 2005 ASTM F468M-05a Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 2005 ASTM F468M-05 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 2003 ASTM F468M-03a Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 2003 ASTM F468M-03 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 2001 ASTM F468M-01a Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 2001 ASTM F468-01e1 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
- 2001 ASTM F468M-01 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- 1998 ASTM F468M-98 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
