ASTM E1032-19
Standard Practice for Radiographic Examination of Weldments Using Industrial X-Ray Film

Standard No.

ASTM E1032-19

Release Date

2019

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM E1032-19

Scope

1.1 This practice provides a uniform procedure for radiographic examination of weldments using industrial radiographic film. Requirements expressed in this practice are intended to control the quality of the radiographic images and are not intended for controlling acceptability or quality of welds. 1.2 The radiographic extent, the quality level, and the acceptance criteria to be applied shall be specified in the contract, purchase order, product specification, or drawings. 1.3 The radiographic techniques stated herein provide adequate assurance for defect detectability; however, it is recognized that, for special applications, specific techniques using more or less stringent requirements may be required than those specified. In these cases, the use of alternative radiographic techniques shall be as agreed upon between purchaser and supplier (also see Section 4). 1.4 The values stated in inch-pound units are to be regarded as standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (For more specific safety precautionary information, see Section 9.) 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM E1032-19 Referenced Document

• ASTM E1025 Standard Practice for Design, Manufacture, and Material Grouping Classification of Hole-Type Image Quality Indicators (IQI) Used for Radiology
• ASTM E1079 Standard Practice for Calibration of Transmission Densitometers*， 2021-11-01 Update
• ASTM E1254 Standard Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
• ASTM E1316 Standard Terminology for Nondestructive Examinations*， 2024-02-01 Update
• ASTM E1742 Standard Practice for Radiographic Examination*， 2024-04-21 Update
• ASTM E1815 Standard Test Method for Classification of Film Systems for Industrial Radiography
• ASTM E242 Standard Reference Radiographs for Appearances of Radiographic Images as Certain Parameters Are Changed
• ASTM E390 Standard Reference Radiographs for Steel Fusion Welds
• ASTM E543 Standard Practice for Agencies Performing Nondestructive Testing
• ASTM E747 Standard Practice for Design, Manufacture and Material Grouping Classification of Wire Image Quality Indicators (IQI) Used for Radiology
• ASTM E94 Standard Guide for Radiographic Examination*， 2024-04-21 Update
• ASTM E999 Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing
• ISO 17636 Non-destructive testing of welds - Radiographic testing of fusion-welded joints
• ISO 5579 Non-destructive testing.Radiographic testing of metallic materials using film and X- or gamma rays.Basic rules
• ISO 9712 Non-destructive testing — Qualification and certification of NDT personnel*， 2021-12-21 Update

ASTM E1032-19 history

• 2019 ASTM E1032-19 Standard Practice for Radiographic Examination of Weldments Using Industrial X-Ray Film
• 2012 ASTM E1032-12 Standard Test Method for Radiographic Examination of Weldments
• 2006 ASTM E1032-06 Standard Test Method for Radiographic Examination of Weldments
• 2001 ASTM E1032-01 Standard Test Method for Radiographic Examination of Weldments
• 1995 ASTM E1032-95 Standard Test Method for Radiographic Examination of Weldments