ASTM F942-18
Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
- Standard No.
- ASTM F942-18
- Release Date
- 2018
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM F942-18(2023)e1
- Latest
- ASTM F942-18(2023)e1
- Scope
- 1.1 This guide summarizes the standard test methods available for determining physical and mechanical characteristics of interlayer materials used in multi-ply aerospace transparent enclosures. 1.2 Interlayer materials are used to laminate glass-to-glass, glass-to-plastic, and plastic-to-plastic. Interlayer materials are basically transparent adhesives with high-quality optical properties. They can also serve as an energy absorbing medium, a fail-safe membrane to contain cockpit pressure and to prevent entry of impact debris; a strain insulator to accommodate different thermal expansion rates of members being laminated and as an adherent to prevent spalling of inner surface ply material fragments. The relative importance of an interlayer characteristic will be a function of the prime use it serves in its particular application. 1.3 This guide, as a summary of various methods in Section 2, is intended to facilitate the selection of tests that can be applied to interlayer materials. 1.4 The test methods listed are for use in determining basic design characteristics and in assuring lot-to-lot uniformity of the materials being tested except as noted in 3.3. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F942-18 Referenced Document
- ASTM C177 Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
- ASTM D1003 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
- ASTM D1004 Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting
- ASTM D1045 Standard Test Methods for Sampling and Testing Plasticizers Used in Plastics
- ASTM D1204 Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature
- ASTM D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
- ASTM D1824 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates
- ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-21 Update
- ASTM D2766 Standard Test Method for Specific Heat of Liquids and Solids
- ASTM D2857 Standard Practice for Dilute Solution Viscosity of Polymers
- ASTM D3167 Standard Test Method for Floating Roller Peel Resistance of Adhesives
- ASTM D3418 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
- ASTM D3465 Standard Guide for Purity of Monomeric Plasticizers by Gas Chromatography*， 2021-07-01 Update
- ASTM D3835 Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
- ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers8212;Tension
- ASTM D542 Standard Test Method for Index of Refraction of Transparent Organic Plastics*， 2022-09-01 Update
- ASTM D570 Standard Test Method for Water Absorption of Plastics*， 2018-08-01 Update
- ASTM D696 Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between -30176C and 30176C With a Vitreous Silica Dilatometer
- ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
- ASTM E1530 Standard Test Method for Evaluating the Resistance to Thermal Transmission of Thin Specimens of Materials by the Guarded Heat Flow Meter Technique
- ASTM E1640 Standard Test Method for Assignment of the Glass Transition Temperature By Dynamic Mechanical Analysis
- ASTM E313 Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
- ASTM F1164 Standard Test Method for Evaluation of Transparent Plastics Exposed to Accelerated Weathering Combined with Biaxial Stress
- ASTM F1316 Standard Test Method for Measuring the Transmissivity of Transparent Parts
- ASTM F1362 Standard Test Method for Shear Strength and Shear Modulus of Aerospace Glazing Interlayer Materials
- ASTM F520 Standard Test Method for Environmental Resistance of Aerospace Transparencies
- ASTM F521 Standard Test Methods for Bond Integrity of Transparent Laminates
ASTM F942-18 history
- 2023 ASTM F942-18(2023)e1 Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
- 2018 ASTM F942-18 Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
- 2002 ASTM F942-02(2013) Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
- 2002 ASTM F942-02(2008) Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
- 2002 ASTM F942-02 Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
- 1993 ASTM F942-93 Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
