ASTM D3575-20
Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers

Standard No.

ASTM D3575-20

Release Date

2020

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D3575-20

Scope

1.1 These test methods apply to flexible closed cell materials made from olefin polymers or blends of olefin polymers with other polymers as defined in Section 3. 1.2 These test methods cover test procedures only. Product requirements are outlined in Specification D4819. 1.3 Unless specifically stated otherwise, by agreement between the purchaser and supplier, all tests shall be performed in accordance with the test methods specified in this standard. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This standard and ISO 7214 address the same subject matter, but differ in technical content. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D3575-20 Referenced Document

• ASTM C177 Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
• ASTM C518 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
• ASTM D1056 Standard Specification for Sponge and Expanded Cellular Rubber Products
• ASTM D1349 Standard Practice for Rubber-Standard Temperatures for Testing
• ASTM D1596 Standard Test Method for Dynamic Shock Cushioning Characteristics of Packaging Material
• ASTM D1667 Standard Specification for Flexible Cellular Materials-Vinyl Chloride Polymers and Copolymers (Closed-Cell Foam)
• ASTM D2863 Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-like Combustion of Plastics (Oxygen Index)
• ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers8212;Tension
• ASTM D4819 Standard Specification for Flexible Cellular Materials Made From Polyolefin Plastics
• ASTM D624 Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
• ASTM D883 Standard Terminology Relating to Plastics
• ASTM E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
• ASTM E2935 Standard Practice for Evaluating Equivalence of Two Testing Processes
• ASTM E456 Standard Terminology for Relating to Quality and Statistics
• ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
• ASTM F355 Standard Test Method for Shock-Absorbing Properties of Playing Surface Systems and Materials

ASTM D3575-20 history

• 2020 ASTM D3575-20 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers
• 2014 ASTM D3575-14 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers
• 2008 ASTM D3575-08 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers
• 2000 ASTM D3575-00e1 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers
• 2000 ASTM D3575-00 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers
• 1991 ASTM D3575-91 Standard Test Methods for Flexible Cellular Materials Made From Olefin Polymers