ASTM C1481-12(2017)
Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
- Standard No.
- ASTM C1481-12(2017)
- Release Date
- 2012
- Published By
- American Society for Testing and Materials (ASTM)
- Latest
- ASTM C1481-12(2017)
- Scope
4.1 The intent of this guide is to provide information and guidelines for consideration by the designer or applicator of joint seals in, or adjacent to, EIFS. Refer to Specification E2568 for additional information pertaining to specifying Class PB EIFS. Refer to Guide E2511 for additional information pertaining to detailing of EIFS-Clad Wall Assemblies.
4.2 Proper selection and use of a sealant is fundamental to its ultimate performance, service life, and durability. A sealant joint subjected to movement and other similar performance factors should be designed for the particular application to avoid compromising its performance capability and causing failures. Refer to C1193 for guidance.
4.3 In addition to the design and installation data in this guide, consult the sealant manufacturer about applications for its products and their proper use and installation.
1.1 This guide describes the use of single and multi-component, cold-applied joint sealants, or precured sealant systems for joint sealing applications, or both, in buildings using Exterior Insulation and Finish Systems (EIFS) on one or both sides of the joint. Refer to 10.1 for joint seal geometries.
1.2 The elastomeric sealants described by this guide meet the requirements of Specifications C834, C920, or C1311.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 There are no ISO standards similar or equivalent to this ASTM standard.
ASTM C1481-12(2017) Referenced Document
- ASTM C1193 Standard Guide for Use of Joint Sealants
- ASTM C1311 Standard Specification for Solvent Release Sealants
- ASTM C1382 Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints
- ASTM C1397 Standard Practice for Application of Class PB Exterior Insulation and Finish Systems
- ASTM C1472 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
- ASTM C717 Standard Terminology of Building Seals and Sealants
- ASTM C719 Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
- ASTM C794 Standard Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
- ASTM C834 Standard Specification for Latex Sealing Compounds
- ASTM C920 Standard Specification for Elastomeric Joint Sealants
- ASTM E2110 Standard Terminology for Exterior Insulation and Finish Systems (EIFS)
- ASTM E2511 Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies
- ASTM E2568 Standard Specification for PB Exterior Insulation and Finish Systems
ASTM C1481-12(2017) history
- 2012 ASTM C1481-12(2017) Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
- 2012 ASTM C1481-12 Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
- 2011 ASTM C1481-11 Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
- 2000 ASTM C1481-00(2006) Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
- 2000 ASTM C1481-00 Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
