ISO 11297-3:2018
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes

Standard No.

ISO 11297-3:2018

Release Date

2018

Published By

International Organization for Standardization (ISO)

Latest

ISO 11297-3:2018

Scope

This document, in conjunction with ISO 11297-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner, as well as associated fittings and joints for the construction of the lining system. It is not applicable to PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe. It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of 20 °C as the reference temperature. NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see

ISO 11297-3:2018 Referenced Document

• EN 12201-1:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General
• EN 12201-2:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes (Incorporates Amendment A1: 2013)
• EN 12201-4:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
• EN 12201-5:2011 Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
• ISO 11297-1:2018 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General
• ISO 12176-1:2017 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
• ISO 12176-2:2008 Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 2: Electrofusion
• ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions
• ISO 3:1973 Preferred numbers; Series of preferred numbers
• ISO 4427-1:2007 Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 1: General
• ISO 4427-2:2007 Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 2: Pipes
• ISO 4427-3:2007 Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 3: Fittings
• ISO 4427-5:2007 Plastics piping systems - Polyethylene (PE) pipes and fittings for water supply - Part 5: Fitness for purpose of the system
• ISO 8772:2006 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE)
• ISO 9967:2016 Thermoplastics pipes - Determination of creep ratio

ISO 11297-3:2018 history

• 2018 ISO 11297-3:2018 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes
• 2013 ISO 11297-3:2013 Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 3: Lining with close-fit pipes