DIN EN 13507:2018
Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying; German version EN 13507:2018
- Standard No.
- DIN EN 13507:2018
- Release Date
- 2018
- Published By
- German Institute for Standardization
- Status
- Replace By
- DIN EN 13507:2018-10
- Latest
- DIN EN 13507:2018-10
- Replace
- DIN EN 13507:2010 DIN EN 13507:2016
- Scope
- This European Standard specifies the processing of surface preparation for thermal spraying. Important principles indicated in this European Standard should be taken into consideration when surfaces of metallic parts are to be prepared for thermal spraying. This European Standard applies to production of new parts as well as for the repair of worn parts.This European Standard does not apply to thermal spraying in the case of protection against atmospheric corrosion by coatings of zinc and/or aluminium and their alloys, for which EN ISO 2063 applies.
DIN EN 13507:2018 Referenced Document
- EN 15520:2007 Thermal spraying - Recommendations for constructional design of components with thermally sprayed coatings
- EN ISO 11124-1:1997 Preparation of Steel Substrates Before Application of Paints and Related Products - Specifications for Metallic Blast-Cleaning Abrasives - Part 1: General Introduction and Classification
- EN ISO 11124-2:1997 Preparation of Steel Substrates before Application of Paints and Related Products - Specifications for Metallic Blast-Cleaning Abrasives - Part 2: Chilled-Iron Grit
- EN ISO 11124-3:1997 Preparation of Steel Substrates before Application of Paints and Related Products - Specifications for Metallic Blast-Cleaning Abrasives - Part 3: High-Carbon Cast-Steel Shot and Grit
- EN ISO 11124-4:1997 Preparation of Steel Substrates before Application of Paints and Related Products - Specifications for Metallic Blast-Cleaning Abrasives - Part 4: Low-Carbon Cast-Steel Shot
- EN ISO 11126-10:2017 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 10: Almandite garnet
- EN ISO 11126-1:1997 Preparation of Steel Substrates Before Application of Paints and Related Products - Specifications for Non-Metallic Blast-Cleaning Abrasives - Part 1: General Introduction and Classification ISO 11126-1: 1993, Including Technical Corrigenda 1: 1997 and 2
- EN ISO 11126-3:1997 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 3: Copper refinery slag ISO 11126-3: 1993
- EN ISO 11126-4:1998 Preparation of Steel Substrates Before Application of Paints and Related Products - Specifications for Non-Metallic Blast- Cleaning Abrasives - Part 4: Coal Furnance Slag ISO 11126-4: 1993
- EN ISO 11126-5:1998 Preparation of Steel Substrates Before Application of Paints and Related Products - Specifications for Non-Metallic Blast- Cleaning Abrasives - Part 5: Nickel Refrinery Slag ISO 11126-5: 1993
- EN ISO 11126-6:1997 Preparation of Steel Substrates Before Application of Paints and Related Products - Specifications for Non-Metallic Blast-Cleaning Abrasives - Part 6:Iron Furnace Slag ISO 11126-6: 1993
- EN ISO 11126-7:1999 Preparation of Steel Substrates Before Application of Paints and Related Products - Specifications for Non-Metallic Blast-Cleaning Abrasives - Part 7: Fused Aluminium Oxide ISO 11126-7: 1995, Including Technical Corrigendum 1: 1999
- EN ISO 11126-8:1997 Preparation of steel substrates before application of paints and related products Specifications for non-metallic blast-cleaning abrasives Part 8: Olivine sand ISO 11126-8: 1993
- EN ISO 11126-9:2004 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 9: Staurolite*， 2024-04-20 Update
- EN ISO 12944-4:2017 Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 4: Types of surface and surface preparation
- EN ISO 2063-1:2017 Thermal spraying - Zinc@ aluminium and their alloys - Part 1: Design considerations and quality requirements for corrosion protection systems
- EN ISO 2063-2:2017 Thermal spraying - Zinc@ aluminium and their alloys - Part 2: Execution of corrosion protection systems
- EN ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel subtrates after overall removal of previous
- EN ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abra
- EN ISO 8503-2:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator proced
- EN ISO 8503-3:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 3: Method for the calibration of ISO surface profile comparators and for the determination of su
- EN ISO 8503-4:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for the calibration of ISO surface profile comparators and for the determination of su
DIN EN 13507:2018 history
- 2018 DIN EN 13507:2018-10 Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying; German version EN 13507:2018
- 2018 DIN EN 13507:2018 Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying; German version EN 13507:2018
- 2010 DIN EN 13507:2010 Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying; German version EN 13507:2010
