DIN 80705:2018
Thin nuts with small widths across flats - Coarse pitch thread, fine pitch thread

Standard No.

DIN 80705:2018

Release Date

2018

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN 80705:2018-07

Latest

DIN 80705:2018-07

Replace

DIN 80705:1990 DIN 80705:2017

Scope

This standard specifies thin nuts with small widths across flats for accessories of lifting gears, especially shackles, but also used as counter nuts for bulkhead pieces.

DIN 80705:2018 Referenced Document

• DIN 13-10:1999 ISO general purpose metric screw threads - Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mm
• DIN 13-1:1999 ISO general purpose metric screw threads - Part 1: Nominal sizes for coarse pitch threads; nominal diameter from 1 mm to 68 mm
• DIN 13-6:1999 ISO general purpose metric screw threads - Part 6: Nominal sizes for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300 mm
• DIN 13-7:1999 ISO general purpose metric screw threads - Part 7: Nominal sizes for 2 mm fine pitch threads; nominal diameter from 17 mm to 300 mm
• DIN 2353:2013 Non-soldering compression fittings with cutting ring.Complete fittings and survey
• DIN 267-24:2007 Fasteners - Technical delivery conditions - Part 24: Hardness classes for nuts without specified proof load values
• DIN 267-2:2017 Fasteners - Technical specification, surface roughness for product classes A and B
• DIN 475-1:2016 Widths across flats for bolts, screws, valves and fittings
• DIN 82016:2010 Cargo lifting gear - Accessories and fittings for lifting and mooring - Cargo shackles
• DIN 82101:2005 Components for lifting, towing, lashing - Shackle, dee - Non-alloy quality steel
• DIN EN 28839:1991 Mechanical properties of fasteners; nonferrous metal bolts, screws, studs and nuts (ISO 8839:1986); german version EN 28839:1991
• DIN EN ISO 10684:2011 Fasteners - Hot dip galvanized coatings (ISO 10684:2004 + Cor. 1:2008); German version EN ISO 10684:2004 + AC:2009
• DIN EN ISO 3269:2000 Fasteners - Acceptance inspection (ISO 3269:2000); German version EN ISO 3269:2000
• DIN EN ISO 4042:2001 Fasteners - Electroplated coatings (ISO 4042:1999); German version EN ISO 4042:1999
• DIN EN ISO 4759-1:2001 Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts; Product grades A, B and C (ISO 4759-1:2000); German version EN ISO 4759-1:2000
• DIN EN ISO 6157-2:2004 Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995); German version EN ISO 6157-2:2004
• DIN ISO 2768-1:1991 General tolerances; tolerances for linear and angular dimensions without individual tolerance indications; identical with ISO 2768-1:1989
• DIN ISO 8992:2005 Fasteners - General requirements for bolts, screws, studs and nuts (ISO 8992:2005)
• DIN ISO 965-1:2017 ISO general purpose metric screw threads - Tolerances - Part 1: Principles and basic data (ISO 965-1:2013)

DIN 80705:2018 history

• 2018 DIN 80705:2018-07 Thin nuts with small widths across flats - Coarse pitch thread, fine pitch thread
• 2018 DIN 80705:2018 Thin nuts with small widths across flats - Coarse pitch thread, fine pitch thread
• 1990 DIN 80705:1990 Thin nuts with coarse pitch and fine pitch thread and with small widths across flats
• 0000 DIN 80705:1969