ISO 8178-6:2018
Reciprocating internal combustion engines - Exhaust emission measurement - Part 6: Report of measuring results and test

Standard No.

ISO 8178-6:2018

Release Date

2018

Published By

International Organization for Standardization (ISO)

Latest

ISO 8178-6:2018

Scope

This document specifies a data format for reporting the measurement results of exhaust emissions from RIC engines for mobile, transportable and stationary use, excluding engines for motor vehicles primarily designed for road use. It includes basic information of the engine being tested. Equivalent data formats including those that are electronically generated can be used as long as the required engine, test cell and test data information is made available. This document applies to measurement in the laboratory and, where applicable, at site. For engines used in machinery covered by additional requirements (e.g. occupational health and safety regulations, dust regulations for powerplants), additional test conditions and special evaluation methods can apply. NOTE Since the report format defined in this document is intended to be applicable to all types of internal combustion engines, some items are, in certain cases, not necessary for specific engines and/or tests, especially when measuring on site. On the other hand, some additional items can be necessary according to test purposes. Deletion and addition of items to be reported are based on agreement between the parties involved.

ISO 8178-6:2018 Referenced Document

• EN 116:2015 Diesel and domestic heating fuels - Determination of cold filter plugging point - Stepwise cooling bath method
• ISO 2160:1998 Petroleum products - Corrosiveness to copper - Copper strip test
• ISO 2719:2016 Determination of flash point - Pensky-Martens closed cup method
• ISO 3007:1999 Petroleum products and crude petroleum - Determination of vapour pressure - Reid method
• ISO 3015:1992 Petroleum products; determination of cloud point
• ISO 3016:1994 Petroleum products - Determination of pour point
• ISO 3104:1994 Petroleum products - Transparent and opaque liquids - Determination of kinematic viscosity and calculation of dynamic viscosity
• ISO 3405:2011 Petroleum products - Determination of distillation characteristics at atmospheric pressure
• ISO 3675:1998 Crude petroleum and liquid petroleum products - Laboratory determination of density - Hydrometer method
• ISO 3733:1999 Petroleum products and bituminous materials - Determination of water - Distillation method
• ISO 3735:1999 Crude petroleum and fuel oils - Determination of sediment - Extraction method
• ISO 3830:1993 Petroleum products; determination of lead content of gasoline; iodine monochloride method
• ISO 3837:1993 Liquid petroleum products; determination of hydrocarbon types; fluorescent indicator adsorption method
• ISO 4260:1987 Petroleum products and hydrocarbons; Determination of sulfur content; Wickbold combustion method
• ISO 4264:2007 Petroleum products - Calculation of cetane index of middle-distillate fuels by the four-variable equation
• ISO 5163:2014 Petroleum products - Determination of knock characteristics of motor and aviation fuels - Motor method
• ISO 5164:2014 Petroleum products - Determination of knock characteristics of motor fuels - Research method
• ISO 5165:2017 Petroleum products - Determination of the ignition quality of diesel fuels - Cetane engine method
• ISO 6245:2001 Petroleum products - Determination of ash
• ISO 6246:2017 Petroleum products - Gum content of fuels - Jet evaporation method
• ISO 660:2009 Animal and vegetable fats and oils - Determination of acid value and acidity
• ISO 6615:1993 Petroleum products; determination of carbon residue; Conradson method
• ISO 7536:1994 Petroleum products - Determination of oxidation stability of gasoline - Induction period method
• ISO 8178-10:2002 Reciprocating internal combustion engines - Exhaust emission measurement - Part 10: Test cycles and test procedures for field measurements of exhaust gas smoke emissions from compression ignition engines operating under transient conditions
• ISO 8178-1:2017 Reciprocating internal combustion engines - Exhaust emission measurement - Part 1: Test-bed measurement systems of gaseous and particulate emissions
• ISO 8178-2:2008 Reciprocating internal combustion engines - Exhaust emission measurement - Part 2: Measurement of gaseous and particulate exhaust emissions under field conditions
• ISO 8178-3:1994 Reciprocating internal combustion engines - Exhaust emission measurement - Part 3: Definitions and methods of measurement of exhaust gas smoke under steady-state conditions
• ISO 8178-4:2017 Reciprocating internal combustion engines - Exhaust emission measurement - Part 4: Steady-state and transient test cycles for different engine applications
• ISO 8178-5:2015 Reciprocating internal combustion engines - Exhaust emission measurement - Part 5: Test fuels
• ISO 8178-6:2000 Reciprocating internal combustion engines - Exhaust emission measurement - Part 6: Report of measuring results and test
• ISO 8178-7:2015 Reciprocating internal combustion engines - Exhaust emission measurement - Part 7: Engine family determination
• ISO 8178-8:2015 Reciprocating internal combustion engines - Exhaust emission measurement - Part 8: Engine group determination
• ISO 8178-9:2012 Reciprocating internal combustion engines - Exhaust emission measurement - Part 9: Test cycles and test procedures for test bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transient conditions
• ISO 8217 Petroleum products - Fuels (class F) - Specifications of marine fuels

ISO 8178-6:2018 history

• 2018 ISO 8178-6:2018 Reciprocating internal combustion engines - Exhaust emission measurement - Part 6: Report of measuring results and test
• 2000 ISO 8178-6:2000 Reciprocating internal combustion engines - Exhaust emission measurement - Part 6: Report of measuring results and test