DIN EN 61800-5-1:2017
Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy (IEC 61800-5-1:2007 + A1:2016); German version EN 61800-5-1:2007 + A1:2017

Standard No.

DIN EN 61800-5-1:2017

Release Date

2017

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN 61800-5-1 E:2018

Latest

DIN EN 61800-5-1/A11:2021

Replace

DIN EN 61800-5-1:2008 DIN EN 61800-5-1 Berichtigung 1:2010 DIN EN 61800-5-1 Berichtigung 2:2014 DIN EN 61800-5-1/A1:2015

Scope

This part of IEC 61800 specifies requirements for adjustable speed power drive systems, or their elements, with respect to electrical, thermal and energy safety considerations. It does not cover the driven equipment except for interface requirements. It applies to adjustable speed electric drive systems which include the power conversion, drive control, and motor or motors. Excluded are traction and electric vehicle drives. It applies to d.c. drive systems connected to line voltages up to 1 kV a.c., 50 Hz or 60 Hz and a.c. drive systems with converter input voltages up to 35 kV, 50 Hz or 60 Hz and output voltages up to 35 kV.

DIN EN 61800-5-1:2017 Referenced Document

• DIN EN 60034-11:2005 Rotating electrical machines - Part 11: Thermal protection (IEC 60034-11:2004); German version EN 60034-11:2004
• DIN EN 60034-12:2008 Rotating electrical machines - Part 12: Starting performance of single-speed three-phase cage induction motors (IEC 60034-12:2002 + A1:2007); German version EN 60034-12:2002 + A1:2007
• DIN EN 60034-14:2008 Rotating electrical machines - Part 14: Mechanical vibration of certain machines with shaft heights 56 mm and higher - Measurement, evaluation and limits of vibration severity (IEC 60034-14:2003 + A1:2007); German version EN 60034-14:2004 + A1:2007
• DIN EN 60034-15:2010 Rotating electrical machines - Part 15: Impulse voltage withstand levels of form-wound stator coils for rotating a.c. machines (IEC 60034-15:2009); German version EN 60034-15:2009
• DIN EN 60034-16-1:2011 Rotating electrical machines - Part 16-1: Excitation systems for synchronous machines - Definitions (IEC 60034-16-1:2011); German version EN 60034-16-1:2011
• DIN EN 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines (IEC 60034-18-1:2010); German version EN 60034-18-1:2010
• DIN EN 60034-18-21:2013 Rotating electrical machines - Part 18-21: Functional evaluation of insulation systems - Test procedures for wire-wound windings - Thermal evaluation and classification (IEC 60034-18-21:2012); German version EN 60034-18-21:2013
• DIN EN 60034-18-22:2001 Rotating electrical machines - Part 18-22: Functional evaluation of insulation systems; Test procedures for wire-wound-windings; Classification of changes and insulation component substitutions (IEC 60034-18-22:2000); German version EN 60034-18-22:2001
• DIN EN 60034-18-31:2013 Rotating electrical machines.Part 18-31: Functional evaluation of insulation systems.Test procedures for form-wound windings.Thermal evaluation and classification of insulation systems used in rotating machines (IEC 60034-18-31:2012); German version EN 60
• DIN EN 60034-18-32:2011 Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance (IEC 60034-18-32:2010); German version EN 60034-18-32:2010
• DIN EN 60034-1:2011 Rotating electrical machines - Part 1: Rating and performance (IEC 60034-1:2010, modified); German version EN 60034-1:2010 + Cor.:2010
• DIN EN 60034-2-1:2015 Rotating electrical machines - Part 2-1: Standard methods for determining losses and efficiency from tests (excluding machines for traction vehicles) (IEC 60034-2-1:2014); German version EN 60034-2-1:2014
• DIN EN 60034-2-2:2010 Rotating electrical machines - Part 2-2: Specific methods for determining separate losses of large machines from tests - Supplement to IEC 60034-2-1 (IEC 60034-2-2:2010); German version EN 60034-2-2:2010
• DIN EN 60034-3:2009 Rotating electrical machines - Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines (IEC 60034-3:2007); German version EN 60034-3:2008
• DIN EN 60034-4:2009 Rotating electrical machines - Part 4: Methods for determining synchronous machine quantities from tests (IEC 60034-4:2008); German version EN 60034-4:2008
• DIN EN 60034-5:2007 Rotating electrical machines - Part 5: Degrees of protection provided by integral design of rotating electrical machines (IP code) - Classification (IEC 60034-5:2000 + Corrigendum 2001 + A1:2006); German version EN 60034-5:2001 + A1:2007
• DIN EN 60034-6:1996 Rotating electrical machines - Part 6: Methods of cooling (IC-Code) (IEC 60034-6:1991); German version EN 60034-6:1993
• DIN EN 60034-7:2001 Rotating electrical machines - Part 7: Classification of types of construction, mounting arrangements and terminal box position (IM code) (IEC 60034-7:1992 + A1:2000); German version EN 60034-7:1993 + A1:2001
• DIN EN 60034-8:2014 Rotating electrical machines - Part 8: Terminal markings and direction of rotation (IEC 60034-8:2007 + A1:2014); German version EN 60034-8:2007 + A1:2014
• DIN EN 60034-9 Berichtigung 1:2008 Rotating electrical machines - Part 9: Noise limits (IEC 60034-9:2003, modified + A1:2007); German version EN 60034-9:2005 + A1:2007, Corrigenda to DIN EN 60034-9 (VDE 0530-9):2008-01
• DIN EN 60034-9:2008 Rotating electrical machines - Part 9: Noise limits (IEC 60034-9:2003, modified + A1:2007); German version EN 60034-9:2005 + A1:2007

DIN EN 61800-5-1:2017 history

• 2021 DIN EN 61800-5-1/A11:2021 Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy; German version EN 61800-5-1:2007/A11:2021
• 2018 DIN EN 61800-5-1 E:2018 Draft Document - Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy (IEC 22G/370/CD:2017); Text in German and English
• 2017 DIN EN 61800-5-1:2017 Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy (IEC 61800-5-1:2007 + A1:2016); German version EN 61800-5-1:2007 + A1:2017
• 2008 DIN EN 61800-5-1:2008 Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy (IEC 61800-5-1:2007); German version EN 61800-5-1:2007
• 0000 DIN EN 61800-5-1 Berichtigung 2:2006
• 0000 DIN EN 61800-5-1 Berichtigung 1:2004
• 0000 DIN EN 61800-5-1:2003