This document describes the fundamental construction and testing requirements for Concentrator Photovoltaic (CPV) modules and assemblies in order to provide safe electrical and mechanical operation during their expected lifetime. Specific topics are provided to assess the prevention of electrical shock, fire hazards, and personal injury due to mechanical and environmental stresses. This document attempts to define the basic requirements for various application classes of concentrator photovoltaic modules and assemblies, but it cannot be considered to encompass all national and regional codes. This document is designed so that its test sequence can coordinate with those of IEC 62108, so that a single set of samples may be used to perform both the safety and performance evaluation of a CPV module and assembly. CPV modules that are constructed in the flat plate module format and operate at 3X and less geometric concentration ratio are considered for evaluation to IEC 61730-1 and IEC 61730-2.
IEC 62688:2017 Referenced Document
ASTM D1002-10 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)*, 2024-04-20 Update
ASTM D257-14 Standard Test Methods for DC Resistance or Conductance of Insulating Materials*, 2024-04-20 Update
ASTM D3755-14 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Under Direct-Voltage Stress*, 2024-04-20 Update
ASTM E162-16 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source
IEC 60060-1:2010 High-voltage test techniques - Part 1: General definitions and test requirements
IEC 60065:2014 Audio, video and similar electronic apparatus - Safety-requirements
IEC 60112:2003 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60216-5:2008 Electrical insulating materials - Thermal endurance properties - Part 5: Determination of relative thermal endurance index (RTE) of an insulating material
IEC 60243-2:2013 Electric strength of insulating materials - Test methods - Part 2: Additional requirements for tests using direct voltage
IEC 60529:1989 Degrees of protection provided by enclosures (IP code)
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 60664-3:2016 Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution
IEC 60695-1-10:2016 Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
IEC 60695-1-11:2014 Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment
IEC 60695-11-20:2015 Fire hazard testing - Part 11-20: Test flames - 500 W flame test method
IEC 60695-2-10:2013 Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
IEC 60904-3:2016 Dispositifs photovolta?ques - Partie 3: Principes de mesure des dispositifs solaires photovolta?ques (PV) à usage terrestre incluant les données de l'éclairement spectral de référence (Edition 3.0; Includes Access to Additional Content)
IEC 60947-1:2007 Low-voltage switchgear and controlgear - Part 1: General rules
IEC 60950-1:2005 Information technology equipment - Safety - Part 1: General requirements
IEC 61032:1997 Protection of persons and equipment by enclosures - Probes for verification
IEC 61140:2016 Protection against electric shock - Common aspects for installations and equipment
IEC 61215-2:2016 Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 2: Test procedures