ASTM D3967-16
Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens

Standard No.

ASTM D3967-16

Release Date

2016

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM D3967-23

Latest

ASTM D3967-23

Scope

5.1 By definition the tensile strength is obtained by the direct tensile test. However, the direct tensile test is difficult and expensive for routine application. The splitting tensile test appears to offer a desirable alternative, because it is much simpler and inexpensive. Furthermore, engineers involved in rock mechanics design usually deal with complicated stress fields, including various combinations of compressive and tensile stress fields. Under such conditions, the tensile strength should be obtained with the presence of compressive stresses to be representative of the field conditions.

5.2 The splitting tensile strength test is one of the simplest tests in which such stress fields occur. Also, by testing across different diametrical directions, possible variations in tensile strength for anisotropic rocks can be determined. Since it is widely used in practice, a uniform test method is needed for data to be comparable. A uniform test is also needed to make sure that the disk specimens break diametrically due to tensile stresses perpendicular to the loading diameter.

Note 2: The quality of the results produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.

1.1 This test method covers testing apparatus, specimen preparation, and testing procedures for determining the splitting tensile strength of rock by diametral line compression of disk shape specimens.

Note 1: The tensile strength of rock determined by tests other than the straight pull test is designated as the “indirect” tensile strength and, specifically, the value obtained in Section 9 of this test is termed the “splitting” tensile strength.

1.2 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units, which are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this test method.

1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.3.1 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. T......

ASTM D3967-16 Referenced Document

• ASTM D2216 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
• ASTM D3740 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D6026 Standard Practice for Using Significant Digits in Geotechnical Data
• ASTM D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids
• ASTM E2586 Standard Practice for Calculating and Using Basic Statistics
• ASTM E4 Standard Practices for Force Verification of Testing Machines
• ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

ASTM D3967-16 history

• 2023 ASTM D3967-23 Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens with Flat Loading Platens
• 2016 ASTM D3967-16 Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
• 2008 ASTM D3967-08 Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
• 2005 ASTM D3967-05 Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
• 1995 ASTM D3967-95a(2004) Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
• 1995 ASTM D3967-95a(2001) Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
• 1995 ASTM D3967-95a Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens