ASTM B233-97(2016)
Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes

Standard No.

ASTM B233-97(2016)

Release Date

1997

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM B233-97(2021)

Latest

ASTM B233-97(2021)

Scope

1.1 This specification covers aluminum 1350 drawing stock 0.375 in. (9.52 mm) to 1.000 in. (25.40 mm) in diameter, in the tempers shown in Table 1, for drawing into wire for electrical conductors (Explanatory Note 1 and Note 2).

(A) Applicable to stock sizes through 0.500-in. (12.70-mm) diameter. The values to apply for larger sizes in these tempers shall be negotiated at time of inquiry.

1.2 The SI values of density and resistivity are to be regarded as the standard. For all other properties the inch-pound values are to be regarded as standard and the SI units may be approximate.

Note 1: Prior to 1975, aluminum 1350 was designated as EC aluminum.

Note 2: The aluminum and temper designations conform to ANSI H35.1. Aluminum 1350 corresponds to unified numbering system A91350 in accordance with Practice E527.

(A) Analysis shall regularly be made only for the elements specified in this table. If, however, the presence of other elements is suspected or indicated in amounts greater than the specified limits, further analysis shall be made to determine that these elements are not present in amounts in excess of the specified limits.

(A) The equivalent resistivity values for 100 % IACS conductivity were each computed from the fundamental IEC value (¹/₅₈  Ω·mm²/m) using conversion factors each accurate to at least seven significant figures. Corresponding values for other conductivities (aluminum) were derived from these by multiplying by the reciprocal of the conductivity ratios accurate to at least seven significant figures.

(A) For this specification, mean diameter is the average of the maximum diameter and the minimum diameter measured in the same transverse plane along the length.

ASTM B233-97(2016) Referenced Document

• ANSI H35.1 Alloy and Temper Designation Systems for Aluminum*， 2024-04-20 Update
• ASTM B193 Standard Test Method for Resistivity of Electrical Conductor Materials
• ASTM B354 Standard Terminology Relating to Uninsulated Metallic Electrical Conductors*， 1998-04-20 Update
• ASTM B557 Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
• ASTM B830 Standard Specification for Uniform Test Methods and Frequency
• ASTM E227 Standard Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique (Withdrawn 2002)*， 2021-02-18 Update
• ASTM E34 Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
• ASTM E527 Standard Practice for Numbering Metals and Alloys (UNS)
• ASTM E55 Standard Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition

ASTM B233-97(2016) history

• 2021 ASTM B233-97(2021) Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes
• 1997 ASTM B233-97(2016) Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes
• 1997 ASTM B233-97(2012) Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes
• 1997 ASTM B233-97(2007) Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes
• 1997 ASTM B233-97(2003)e1 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes
• 1997 ASTM B233-97 Standard Specification for Aluminum 1350 Drawing Stock for Electrical Purposes