ASTM A109/A109M-16
Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled

Standard No.

ASTM A109/A109M-16

Release Date

2016

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM A109/A109M-16(2018)

Latest

ASTM A109/A109M-24

Scope

1.1 This specification covers cold-rolled carbon steel strip in cut lengths or coils, furnished to closer tolerances than cold-rolled carbon steel sheet, with specific temper, with specific edge or specific finish, and in sizes as follows:

Width, in.	Thickness, in.
Over 1/2 to 2315/16	0.300 and under
Over 12.5 to 600 mm	7.6 mm and under

1.2 Cold-rolled strip is produced with a maximum specified carbon not exceeding 0.25 percent.

1.3 Strip tolerance products may be available in widths wider than 23¹⁵/₁₆ in. [600 mm] by agreement between purchaser and supplier. However, such products are technically classified as cold rolled sheet. The tolerances, finishes, tempers, edges, and available widths and thicknesses differentiate cold rolled strip from the product known as cold rolled sheet which is defined by Specification A568/A568M and from cold rolled high carbon strip which is defined by Specification A682/A682M.

1.4 For the purpose of determining conformance with this specification, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.

1.5 The SI portions of the tables contained herein list permissible variations in dimensions and mass (see Note 1) in SI (metric) units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the “M” specification is used.

Note 1: The term weight is used when inch-pound units are the standard. However, under SI the preferred term is mass.

1.6 The values stat......

ASTM A109/A109M-16 Referenced Document

• ASTM A1073/A1073M Standard Practice for Using Hand Micrometers to Measure the Thickness of Uncoated Steel Sheet and Nonmetallic and Metallic-Coated Steel Sheet
• ASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
• ASTM A568/A568M Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
• ASTM A682/A682M Standard Specification for Steel, Strip, High-Carbon, Cold-Rolled, General Requirements For
• ASTM A700 Standard Practices for Packaging, Marking, and Loading Methods for Steel Products for Domestic Shipment
• ASTM A751 Standard Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
• ASTM A941 Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• ASTM E430 Standard Test Methods for Measurement of Gloss of High-Gloss Surfaces by Goniophotometry

ASTM A109/A109M-16 history

• 2024 ASTM A109/A109M-24 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 2018 ASTM A109/A109M-16(2018) Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 2016 ASTM A109/A109M-16 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 2015 ASTM A109/A109M-15 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 2014 ASTM A109/A109M-14 Standard Specification for Steel, Strip, Carbon 40;0.25 Maximum Percent41;, Cold-Rolled
• 2013 ASTM A109/A109M-13 Standard Specification for Steel, Strip, Carbon lpar;0.25 Maximum Percentrpar;, Cold-Rolled
• 2008 ASTM A109/A109M-08 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 2003 ASTM A109/A109M-03 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 2000 ASTM A109/A109M-00e1 Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 1998 ASTM A109/A109M-98a Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled
• 1993 ASTM A109-93 Standard Specification for Steel, Strip, Carbon, Cold-Rolled - WITHDRAWN - Replaced by A109/A109M-98