ASTM A1044/A1044M-16a
Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- Standard No.
- ASTM A1044/A1044M-16a
- Release Date
- 2016
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM A1044/A1044M-16ae1
- Latest
- ASTM A1044/A1044M-22a
- Scope
1.1 This specification covers steel stud assemblies for shear reinforcement of concrete. Stud assemblies consist of either single-headed studs (Type 1) attached to a structural steel base rail by structural welding or stud welding, or double-headed studs (Type 2) mechanically crimped into a non-structural steel shape or attached to a steel plate by spot welding or tack welding. These stud assemblies are not intended for use as shear connectors in steel-concrete composite construction.
Note 1: The configuration of the studs for stud assemblies is much different than the configuration of the headed-type studs prescribed in Section 7, Figure 7.1 of AWS D1.1/D1.1M. Ratios of the cross-sectional areas of the head-to-shank of the AWS D1.1/D1.1M studs range from about 2.5 to 4. In contrast, this specification requires the area of the head of the studs for stud assemblies to be at least 10 times the area of the shank. Thus, the standard headed-type studs in Section 7, Figure 7.1 of AWS D1.1/D1.1M do not conform to the requirements of this specification for use as stud assemblies for shear reinforcement.
1.2 This specification is applicable for orders in either inch-pound units or in SI units.
1.3 The values stated either in inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
ASTM A1044/A1044M-16a Referenced Document
- ASTM A29/A29M Standard Specification for Steel Bars, Carbon and Alloy, Hot-Wrought and Cold-Finished, General Requirements for
- ASTM A36/A36M Standard Specification for Carbon Structural Steel
- ASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
- ASTM A615/A615M Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
- ASTM A706/A706M Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
- AWS D1.1/D1.1M-2004 Structural Welding Code - Steel
ASTM A1044/A1044M-16a history
- 2022 ASTM A1044/A1044M-22a Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- 2022 ASTM A1044/A1044M-22 Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- 2016 ASTM A1044/A1044M-16ae1 Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- 2016 ASTM A1044/A1044M-16a Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- 2016 ASTM A1044/A1044M-16 Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- 2015 ASTM A1044/A1044M-15 Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- 2005 ASTM A1044/A1044M-05(2010) Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
- 2005 ASTM A1044/A1044M-05 Standard Specification for Steel Stud Assemblies for Shear Reinforcement of Concrete
