ASTM D7714-11(2016)e1
Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
- Standard No.
- ASTM D7714-11(2016)e1
- Release Date
- 2011
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D7714-11(2021)
- Latest
- ASTM D7714-11(2021)
- Scope
1.1 This specification covers the requirements for glycerin base engine coolants used in automobiles or other light duty service cooling systems. When concentrates are used at 50 to 60 % concentration by volume in water, or when prediluted glycerin base engine coolants (50 volume % minimum) are used without further dilution, they will function effectively to provide protection against freezing, boiling, and corrosion.
1.2 The coolants governed by this specification are categorized as follows:
Coolant Type
Description
I
Glycerin base concentrate
II
Glycerin predilute (50 to 60 volume %)
Note 1: This specification is based on the knowledge of the performance of engine coolants prepared from new or virgin ingredients that comply with Specification D7640.
1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See X1.5 and X3.1.3 for specific warning statements.
Note 2: This specification applies to automobiles and light duty service. A glycerin based specification for heavy duty engine service is under development.
ASTM D7714-11(2016)e1 Referenced Document
- ASTM D1119 Standard Test Method for Percent Ash Content of Engine Coolants
- ASTM D1120 Standard Test Method for Boiling Point of Engine Coolants
- ASTM D1121 Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts
- ASTM D1122 Standard Test Method for Density or Relative Density of Engine Coolant Concentrates and Engine Coolants By The Hydrometer
- ASTM D1123 Standard Test Methods for Water in Engine Coolant Concentrate by the Karl Fischer Reagent Method
- ASTM D1126 Standard Test Method for Hardness in Water
- ASTM D1177 Standard Test Method for Freezing Point of Aqueous Engine Coolants
- ASTM D1287 Standard Test Method for pH of Engine Coolants and Antirusts
- ASTM D1293 Standard Test Methods for pH of Water
- ASTM D1384 Standard Test Method for Corrosion Test for Engine Coolants in Glassware
- ASTM D1881 Standard Test Method for Foaming Tendencies of Engine Coolants in Glassware
- ASTM D1882 Standard Test Method for Effect of Cooling System Chemical Solutions on Organic Finishes for Automotive Vehicles
- ASTM D2570 Standard Test Method for Simulated Service Corrosion Testing of Engine Coolants
- ASTM D2809 Standard Test Method for Cavitation Corrosion and Erosion-Corrosion Characteristics of Aluminum Pumps With Engine Coolants
- ASTM D3321 Standard Test Method for Use of the Refractometer for Field Test Determination of the Freezing Point of Aqueous Engine Coolants
- ASTM D3634 Standard Test Method for Trace Chloride Ion in Engine Coolants
- ASTM D4327 Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography
- ASTM D4340 Standard Test Method for Corrosion of Cast Aluminum Alloys in Engine Coolants Under Heat-Rejecting Conditions
- ASTM D4725 Standard Terminology for Engine Coolants
- ASTM D512 Standard Test Methods for Chloride Ion In Water
- ASTM D516 Standard Test Method for Sulfate Ion in Water
- ASTM D5827 Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography
- ASTM D5931 Standard Test Method for Density and Relative Density of Engine Coolant Concentrates and Aqueous Engine Coolants by Digital Density Meter
- ASTM D6130 Standard Test Method for Determination of Silicon and Other Elements in Engine Coolant by Inductively Coupled Plasma-Atomic Emission Spectroscopy
- ASTM D6660 Standard Test Method for Freezing Point of Aqueous Ethylene Glycol Base Engine Coolants by Automatic Phase Transition Method
- ASTM D7640 Standard Specification for Engine Coolant Grade Glycerin
- ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
- ASTM E394 Standard Test Method for Iron in Trace Quantities Using the 1,10-Phenanthroline Method
ASTM D7714-11(2016)e1 history
- 2021 ASTM D7714-11(2021) Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
- 2011 ASTM D7714-11(2016)e1 Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
- 2011 ASTM D7714-11 Standard Specification for Glycerin Base Engine Coolant for Automobile and Light-Duty Service
