ASTM D7583-16
Standard Test Method for John Deere Coolant Cavitation Test

Standard No.
ASTM D7583-16
Release Date
2016
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM D7583-16(2023)
Latest
ASTM D7583-16(2023)
Scope

5.1 This test method was developed to evaluate the ability of a heavy-duty diesel engine coolant to provide protection against damage resulting from a phenomenon known as cylinder liner cavitation corrosion.

5.2 This test method may be used for engine coolant specification acceptance when all details of this test method are in compliance.

5.3 The design of the engine used in this test method is a production OEM diesel engine modified to consistently produce the operating conditions that accelerate damage from cylinder liner cavitation. This factor, along with the accelerated operating conditions needs to be considered when extrapolating test results.

1.1 This test method is commonly referred to as the John Deere Cavitation Test.2 The test method defines a heavy-duty diesel engine to evaluate coolant protection as related to cylinder liner pitting caused by cavitation.

1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. The only exception is where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, and tubing sizes.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A1 for general safety precautions.

1.4 Table of Contents: 

Scope

1

Referenced Documents

2

Terminology

3

Summary of Test Method

ASTM D7583-16 Referenced Document

  • ASTM D1121 Standard Test Method for Reserve Alkalinity of Engine Coolants and Antirusts
  • ASTM D1177 Standard Test Method for Freezing Point of Aqueous Engine Coolants
  • ASTM D1287 Standard Test Method for pH of Engine Coolants and Antirusts
  • ASTM D130 Standard Test Method for Detection of Copper Corrosion from Petroleum Products by the Copper Strip Tarnish Test
  • ASTM D1319 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
  • ASTM D2274 Standard Test Method for Oxidation Stability of Distillate Fuel Oil (Accelerated Method)
  • ASTM D235 Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
  • ASTM D2500 Standard Test Method for Cloud Point of Petroleum Products
  • ASTM D2622 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
  • ASTM D2709 Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge
  • ASTM D287 Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)
  • ASTM D4052 Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter
  • ASTM D445 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity)
  • ASTM D4485 Standard Specification for Performance of Active API Service Category Engine Oils
  • ASTM D4737 Standard Test Method for Calculated Cetane Index by Four Variable Equation
  • ASTM D482 Standard Test Method for Ash from Petroleum Products
  • ASTM D5185 Standard Test Method for Determination of Additive Elements, Wear Metals, and Contaminants in Used Lubricating Oils and Determination of Selected Elements in Base Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)
  • ASTM D524 Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products
  • ASTM D5302 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
  • ASTM D5844 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Rusting (Sequence IID)
  • ASTM D5967 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine
  • ASTM D613 Standard Test Method for Cetane Number of Diesel Fuel Oil
  • ASTM D664 Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration
  • ASTM D86 Standard Test Method for Distillation of Petroleum Products
  • ASTM D93 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester
  • ASTM D97 Standard Test Method for Pour Point of Petroleum Products
  • ASTM D976 Standard Test Methods for Calculated Cetane Index of Distillate Fuels
  • ASTM E202 Standard Test Methods for Analysis of Ethylene Glycols and Propylene Glycols
  • ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
  • ASTM E344 Terminology Relating to Thermometry and Hydrometry

ASTM D7583-16 history

  • 2023 ASTM D7583-16(2023) Standard Test Method for John Deere Coolant Cavitation Test
  • 2016 ASTM D7583-16 Standard Test Method for John Deere Coolant Cavitation Test
  • 2009 ASTM D7583-09 Standard Test Method for John Deere Coolant Cavitation Test
Standard Test Method for John Deere Coolant Cavitation Test


Copyright ©2024 All Rights Reserved